Behringer

Behringer

Brand Since 2019-01-17

Behringer

165,345 members
32,086 posts
  • Muller
    Contributor - Level 1
    2020-06-01

    Bonjour mon nu3000 ne démarre plu depuis hier il reste en rouge le ventillo c lance puis s'arrête rien de branche dessus il marche très bien ya 2 jours hier quand jai branche la prise rien reste en rouge 

    0 20
  • MARTIN55
    Contributor - Level 1
    2020-05-31

    Please can anyone tell me how I program the sliders to use with kontakt please ??

    I want to use the sliders for expression...in Ableton and Cubase

     

    I have a Macbook Catalina

     

    thx

    M

    read more...
    0 32
    • MARTIN55
      DaveMorrison

      @MARTIN55 


      Which model of X-Touch.


      If it's the full-sized X-Touch, then all assignments are done in the DAW. The full-sized X-Touch is just a clone of the mackie control devices (with extra modes for X/M mixer control). 


      Search for using Mackie Control with Ableton and Cubase. Their user forums are a good place to start.

      • May 31, 2020
  • Nijelusa
    Contributor - Level 1
    2020-05-30
    Hello! My name is Nijel and I am still learning much with regards to analog synthesizers, as the Behringer Model D is my first one. I noticed it was out of tune, and did the oscillator calibration following the manual. I was wondering what specifically does the oscillator calibration do (and the meaning of scale and ranges for the oscillators and what changing them does)? Also, what is a more detailed purpose of the pitch CV calibration and the octave range calibration, and why these may need to be done along with the oscillator calibration (for ex. does the pitch cv calibration only affect the 1 V/oct cv input? And would changing Osc 2 octave range on the front panel just throw away the oscillator calibration done for the other octaves?) Thank you!
    read more...
    0 27
  • IanJTurner
    Contributor - Level 1
    2020-05-30

    Hi

    I'm using an X-Touch Compact with Cubase 10.  I understand that Mackie Control functionality will vary, depending on the DAW, and I've found that Cubase's implementation lacks a few key features (compared with Logic, for instance).  Whis this in mind I was hoping to use the X-Touch Compact in MC mode for general mixing, and then switch to Standard mode for more detailed editing. So, I have the X-Touch Compact set up as a Mackie Control device in Cubase, and also as a Generic Remote device.

    I worked out how to switch from MC mode to Standard mode and back without having to power off the device, but I discovered an odd anomoly.  Unless I go into Cubase's device set up and remove the X-Touch Compact from the Mackie Control dialogue, then - when in Standard mode, the buttons on the X-Touch Compact all send what appear to be keyboard shortcut style function commands to Cubase (zooming in and out or starting record or playback, for example) - in addition to the commands that I've set up in the Generic Remote. I can see no way to stop this happening - other than removing the device from the Mackie Control dialogue.  I wonder if anyone here can help with this?

    read more...
    0 24
  • flpccc
    Contributor - Level 1
    2020-05-30

    Hi guys,

    I connected this sweet foot pedal to my PC through the M-Audio Uno USB/midi interface, installed the latest driver downloaded from the M-Audio site and it is working with each bank/pedal corresponding to adequate Guitar Rig preset. Example1: Bank0 / Pedal1 will be 001 preset in Guitar Rig and so on.

     

    My problem is that I am not able to program each bank/pedal to do what I assign it to through Options>Controller. I am only able to program Expression Pedals 1 and 2 however I want. When I try to do exactly the same thing with pedals my input just gets ignored and the preset changes to whatever default value are (see example1 above). I am quite sure I am performing the correct steps as I was able to program EP 1 and 2 with no issues.

     

    My questions is: How do I get Guitar Rig to recognize my pedals and allow me to program them through Options>Controller the way I'm able to program Expression Pedals?

    What piece of information am I missing? Please help me out! I spent many hours trying to work around this to no avail...

    Alternately, I downloaded the FCB1010 Manager which I am trying to figure out as we speak.

     

    Thanks!!

    read more...
    0 24
  • EllisLampman
    Contributor - Level 3
    2020-05-29

    Does running IEM (earbuds) like Westones out of the HA8000 work well? Obviously a 1/4" to 3.5mm adapter is needed, but I'm more concerned with the impedence working with earbuds as opposed to headphones.

    The 1/4" phone jack out of my Mimic Pro drum module sounds terrible with my IEMs, so I think thats an impedance issue with it being designed for over-the-ear headphones.

    Anybody know about this?

    Thanks

    read more...
    0 35
    • EllisLampman
      RexBeckett

      @EllisLampman 


      Westone IEMs usually have an impedance of 19 Ohms. The HA8000 V2 can drive headphones with impedance as low as 8 Ohms so should be fine. The combination of Westone's high sensitivity with the high output level of the HA8000 could make them very loud. Be careful with the level controls!

      • May 29, 2020
  • PW
    Newcomer - Level 2
    2020-05-29

    Hi,

    I have recently bought the UMC22 and I'm concerned about the noise I get, even when there's nothing connected at the input. Please, have a look at the spectrum I got at 100% gain. I guess, that the peak at 50Hz is from my power source (I'm from Europe).

    Is there a way to reduce the noise or is it normal for this low-end products?

    Thanks in advance for your comments.  

    Adnotacja 2020-05-29 154041.png
    read more...
    0 34
    • PW
      RexBeckett

      @PW 


      At full gain and with no input connected, hum at -75dB is not unusual. If the hum is at a similar level when the input is terminated or shorted it might suggest that there is a grounding issue with your configuration.

      • May 29, 2020
  • andresmanosalva
    Contributor - Level 1
    2020-05-29

    Hola, acabo de comprar el mixer Xenix q502usb para grabar con un Microfono B-2Pro en una laptop Dell Inspiron 1420 con Windows 7 Ultimate, para resumir instalè el sotware (Audacity win- 1.2.6) y nada mas, cuando conecto la xenix q502usb a la laptop me anula todo sonido del laptop y cuando intento grabar con el B-2Pro no lo hace y graba con el micro de la laptop. me pueden ayudar a solucionar esto? Muchas Gracias.

    read more...
    0 33
    • andresmanosalva
      RexBeckett

      @andresmanosalva 


      Hello Andres, welcome to the community.


       


      That is a very old version of Audacity. You can get the latest (2.4.1) from Audacity Downloads. There are options in Audacity for the recording input and playback output devices:


      Audacity IO.PNG


      If you cannnot see these, click on View -> Toolbars and enable Device Toolbar.


       


      I don't know how well the B-2 mic will work with the Q502USB. The B-2 requires 48V phantom power but the Q502USB only supplies 15V.

      • May 28, 2020
  • bradd78
    Newcomer - Level 2
    2020-05-28

    Hi guys. I'm looking at buying a MIC2200 and I'm wondering if the Mic/Line switch disables the XLR input if I put it in Line mode? I'm going to use it with a combo jack and want the input to go to the XLR input when I plug in an XLR cable, and the jack input when I plug in a 1/4” cable...

    read more...
    0 18
  • da_bassman
    Contributor - Level 1
    2020-05-28

    Our church just purchased 4 Behringer P-16M's. We are using them in conjuction with a Behringer XR18 digital mixer. The ultranet cable runs from one end of our stage to my P16, which is about 50 feet cable lenght. I'm the bass player. From mine it then is run from my Thru to the IN next in line and on until it reaches the 4th one. Everything out of the mixer to the P16s is fine except for the bass which is intermittent in the P16's only. It's rock solid in the house mix. I can play maybe a measure or two and then the bass just kind of fades out. A few measures later it comes back and then goes away again. Since I'm at the top of line then I know the drummer is experiencing the same intermittent signal so I'm going to assume the other two are also. I've tried moving the bass input to other channels on the mixer but the problem is still there.

    I am stumped so any help would be appreciated. Thanks in advance.

     

     

    read more...
    0 47
    • da_bassman
      Paul_Vannatto

      Hi Glen @da_bassman 


      Check the limiter level (top right knob) on your P16. It is probably turned down. One of the musicians at my church had the same thing happen to him and his limiter was turned down.


       

      • May 28, 2020
Go to page