Statistics

165,363 members
41 posts
  • justinguma
    Newcomer - Level 1
    2020-10-12

    Testing number of post

    0 16
  • sigma
    Triber
    2020-09-22

    afasf

    0 7
  • dhpatel
    Newcomer - Level 3
    2020-09-08

    testt testt

    1 8
  • dhpatel
    Newcomer - Level 3
    2020-06-13
    safsafasf
    1 44
  • __JAG__
    Newcomer - Level 2
    2020-06-08

    Ok just received 4 of the DP48's and updated the firmware this evening. So when in dual mixer mode, when setting the group channel assignments, and channel levels, how do you set them up for each mix A and B? Or are these settings global for both mix A and B? 

    read more...
    0 49
    • __JAG__
      GaryHiggins

      @__JAG__ 


      The sources are the same for both, the mixes of the sources is what can be made different.

      • June 8, 2020
    • __JAG__
      __JAG__

      So the group sources and levels are the same for each, correct? Then you can individually control levels of each group for Mix A and B? That is what I'm seeing. 

      • June 8, 2020
  • EllisLampman
    Contributor - Level 3
    2020-05-29

    Does running IEM (earbuds) like Westones out of the HA8000 work well? Obviously a 1/4" to 3.5mm adapter is needed, but I'm more concerned with the impedence working with earbuds as opposed to headphones.

    The 1/4" phone jack out of my Mimic Pro drum module sounds terrible with my IEMs, so I think thats an impedance issue with it being designed for over-the-ear headphones.

    Anybody know about this?

    Thanks

    read more...
    0 39
    • EllisLampman
      RexBeckett

      @EllisLampman 


      Westone IEMs usually have an impedance of 19 Ohms. The HA8000 V2 can drive headphones with impedance as low as 8 Ohms so should be fine. The combination of Westone's high sensitivity with the high output level of the HA8000 could make them very loud. Be careful with the level controls!

      • May 29, 2020
  • da_bassman
    Contributor - Level 1
    2020-05-28

    Our church just purchased 4 Behringer P-16M's. We are using them in conjuction with a Behringer XR18 digital mixer. The ultranet cable runs from one end of our stage to my P16, which is about 50 feet cable lenght. I'm the bass player. From mine it then is run from my Thru to the IN next in line and on until it reaches the 4th one. Everything out of the mixer to the P16s is fine except for the bass which is intermittent in the P16's only. It's rock solid in the house mix. I can play maybe a measure or two and then the bass just kind of fades out. A few measures later it comes back and then goes away again. Since I'm at the top of line then I know the drummer is experiencing the same intermittent signal so I'm going to assume the other two are also. I've tried moving the bass input to other channels on the mixer but the problem is still there.

    I am stumped so any help would be appreciated. Thanks in advance.

     

     

    read more...
    0 48
    • da_bassman
      Paul_Vannatto

      Hi Glen @da_bassman 


      Check the limiter level (top right knob) on your P16. It is probably turned down. One of the musicians at my church had the same thing happen to him and his limiter was turned down.


       

      • May 28, 2020
  • captainonion
    Contributor - Level 2
    2020-05-28
    Hello, There has been alot of talk, from practically every clerk in the business, about THE specifications for this model. With my applications, I need to know for certain if the MAIN OUTS on this Xenyx QX1002USB are actually interfaced into this mixer balanced TRS, or if these TRS connectors are merely a facade at the top of an unbalanced (TS) output? Thank you!
    read more...
    0 56
    • captainonion
      RexBeckett

      @captainonion 


      On my unit they are impedance balanced TRS outputs. This gives most of the advantages of a fully-balanced output but is more tolerant of connections to unbalanced inputs. The cold side of the output is not driven but has the same impedance (to ground) as the driven, hot side.

      • May 28, 2020
  • brokenbones1
    Contributor - Level 1
    2020-05-15

    Hello,

    Has anyone found a footcontroller that will control a p16m? 

    0 45
    • brokenbones1
      RexBeckett

      @brokenbones1 


      Hello Joseph, welcome to the community.


       


      What parameters on the P16M do you want to control?

      • May 15, 2020
    • brokenbones1
      brokenbones1

      Ideally I would like to have full channel volume control via an onboard expression pedal of all 16 channels on the P16m through the program change and control change #7 functions. I have found an older controller, a Digitech MC2, that looks to be a good candidate but would only control 1 program change at a time. That wouldn't be a deal breaker as opposed to something like the Behringer FCB1010 which is too large of a footprint. I'm wondering if there is a 2 button midi footswitch that is programmable for Program Changes and CC messages that also includes an EXP pedal 1/4" jack. Line 6 offers the FBV controller but it only has a cat5 out. I could look into making a cat5 to midi cable but I don't know if the p16m would power the FBV using that cable. I'm still doing research and brainstorming. If you have any ideas or more knowledge that would get me in the right direction, I would appreciate it.

      • May 15, 2020
  • BillFleming
    Contributor - Level 2
    2020-04-17

    Hello,

    Up until recently we have been running a single P16D distributor to send audio over PoE to our P16Ms; we have the P16D connected into a Midas DL16 stagebox which then connects into a Midas M32 console.

    We recently expanded our stage setup by adding a 2nd DL16 and have installed two wall mounted racks - the racks are located on each side of the stage and each contains one of the DL16s. We would like to add a 2nd P16D so one is located in each rack. The question is can a 2nd P16D be plugged into the Ultranet port on the 2nd DL16 just as the first P16D is plugged into the first DL16? If so are there any configuration settings that need to be tweaked on the M32 to get this to work?

    Thanks, Bill

    read more...
    0 80
    • BillFleming
      GaryHiggins

      @BillFleming 


       


      Hello, should work just fine as long as your aes50 a and b 33-48 are set for p16 1-16-assuming they are on different ports. No issues at all if daisy chained as both carry the same assignment.


       


      Aes50 33-48 is what the ultranet ports of a DL/S16 are fixed at. Default settings for aes50a/b 33-48 on an M/X32 are p16 1-8 and p16 9-16. IF you change either routing group to be something else other than p16, that will be what is carried by that particular DL16's ultranet port. That ability can also be your friend should you WANT different sources on either one....or drive you mad if you don't and wonder why.

      • April 16, 2020
    • BillFleming
      BillFleming

      Thanks Gary, I think I follow.


      You said  "No issues at all if daisy chained as both carry the same assignment." I have both DL16s running off of AES-A which I would also call daisy-chained. I just want to make sure we're on the same page because I work on the board fairly infrequently and the routing interface makes a little more sense to me than it first did a year and a half ago but nonetheless it's still a bit of a mystery. I would love to see a video on M32 routing where it is explained in great detail but also starts out at a high level and is not over in under five minutes - the Midas videos are very good but routing at least in the IT world can be a complex topic in and of itself.


      Once we get the 2nd P16D and plug it in I should be able to get it going. I'm pretty sure our Ultranet ports are still set to their defaults 1-8 and 9-16. I have to head back to the church next week to spin up some Ethernet connections so will check then. I do have a 2nd question regarding how the input port numbers were shifted after I added the 2nd DL16, but I'll start a 2nd thread for that one in case I can't find the answer elsewhere.


      Thanks again. 

      • April 17, 2020
Go to page