165,420 members
161 posts
  • jcsy
    Community Manager

    This is a post with an image attachment.

    1 63
  • RolfTrijber
    Contributor - Level 1

    Hi There,

    Does anyone know how to convert channels from a U-Phoria UMC1820 in Windows 10 to mono?

    Thank you in advance for an answer,

    0 57
    • RolfTrijber

      Hello @RolfTrijber , welcome to the community.


      Windows treats most USB sound devices as stereo. Most DAWs can set tracks as mono or stereo either before or after recording. Which DAW software are you using?

      • March 15, 2020
  • sigma
  • Albertosu
    Contributor - Level 1

    Hola acabo de comprar la tajeta de sonido U-Phoria UMC1820 y no me funciona con windows 8.1 con usb3,

    alguien sabe si es que solo funciona con puertos Usb2.0?Gracias.

    0 53
  • ReinhardKlamm
    Contributor - Level 2

    Anyone using x-Touch compact with Gigperformer or mainstage =  bidirectional midi. 

    0 53
  • PavelFila
    Contributor - Level 1


    I'm getting troubles trying to switch on my Bcf2000.

    Here is video

    Anyone knows what the error means? 

    0 44
  • NGonz
    Contributor - Level 1

    Hello All,

    I just want to state upfront I'm a hobbyist and not well schooled in the fine arts of musical recording. 

    Here is my setup info: I have a Mac OSX (MacBook Pro - Retina, 15-inch, Mid 2014) running Catalina (10.15.3). I'm using Garageband (10.3.4) along with a Behringer UMC202HD 192K. I just putz around and so far this setup works for me as I'm just using it now for the sound effects for my guitar.

    With that being said - here is my problem that I'm hoping somebody has an answer to. I can plug up my guitar to Garageband and everything works, however, after around 3 seconds the guitar input audio drops/cuts-out. I'm not playing loud enough or have enough of an input signal to where it's clipping (and I don't think even if it did clip it would go silent). I'm not well-versed enough (although I am computer technical) to know if this is a noise gate, maybe something with the USB, buffering, or what.

    My input and output are two different sources as I saw some related problem were they thought this could have an impact. I've searched the internet at length and am finding some people that have similar problems but no real solutions.

    Any guideance/support would be appreciated. I do want to start doing some actual recordings but this is driving me nuts.

    Thanks, NG.






    0 43
  • Countrokula
    Contributor - Level 1

    Hey there, quick question, anyone have experience with the monitor 1? I'm looking to install it at my venue, just want to know if I can run audio through the xlr and 3.5mm at the same time? I'd like to have my tvs and ipod hooked up, then balance the signal on the devices, or use one or the other without having to unplug.

    0 42
  • cschmidt01
    Contributor - Level 1

    Hi all, 

    Anyone know the part number for the FCB1010 power cord? I don't believe the cord that came with my controller is the right one. It keeps falling out of the receptacle on the back of the FCB. 


    0 40
    • cschmidt01

      Hi Carl @cschmidt01 ,

      The FCB1010 uses a standard IEC type cable that is identical to a computer power supply cable. I have been getting some of these ends to replace critical cable ends (for my X32 Racks, etc.) that I want to have guaranteed they won't pull out. They lock to the IEC jack very well.


      • April 16, 2020
    • cschmidt01

      yup standard IEC power cable... I have 2 milk crates full of them!!! I am a pakRat!

      • May 21, 2020
  • lwhite2
    Contributor - Level 2

    When using the Editor for the Behringer Mini controller I dump a configuration to Layer A and it's available when the unit is disconnected and reconnected to usb.

    However, when I dump a configuratio to Lay B, the setup disappears after the unit is disconnected.  I have to open the editor and dump to again when I reconnect.  

    Any idea what's going on ?

    0 39
Go to page