Statistics

165,429 members
179 posts
  • WillemKrabbe
    Regular Contributor - Level 1
    2020-01-16

    Hi all,

    I'm trying to cut frequencies above 80 Hz on the wing EQ on Matrix 1. The High cut goes down to 2k and not lower.
    How can I get the High cut frequency down to 80 Hz?

    On the X32 I can get the high cut as low as i want.

     

    Willem

    read more...
    0 506
    • WillemKrabbe
      Paul_Vannatto


      @WillemKrabbe wrote:


      How can I get the High cut frequency down to 80 Hz?





      Actually there is no low or high cut on any of the buses (including matrixes), only low and high shelf. And you are correct - the high shelf only goes down to 2K - not sure why. I will ask.


       

      • January 16, 2020
    • WillemKrabbe
      WillemKrabbe

      Actually when going to the settings of the EQ you can switch the HIGH BAND MODE from SHV to PEQ or CUT, but still the 2kHz stays.


       


      Kind regards,


       


      Willem

      • January 16, 2020
    • WillemKrabbe
      Paul_Vannatto


      @WillemKrabbe wrote:


      Actually when going to the settings of the EQ you can switch the HIGH BAND MODE from SHV to PEQ or CUT





      Thanks Willem. I keep forgetting to hit the gear icon.


       




      but still the 2kHz stays.



      I have been informed that they are working on this.

      • January 16, 2020
  • DennisMilsom
    Contributor - Level 2
    2019-11-11

    I have an XR-16 and I am trying to setup a secure WEP. I have followed all instructions I have found to create a password protected WEP for this, power cycled several times, initialised to factory settings and re-done the whole process five times. It STILL refuses to be accessible via password!

    And I have used the hard reset button on the XR prior to each attempt to set this.

    Using the laptop over WI-FI and under the available networks it only shows the XR as an open network, when I click on it to connect it does not ask for any password even though this has been set in the PC Editing app setup page.

    Can anyone advise exactly how you do setup a secure WEP?

     

    Oh and even via Ethernet (with the switch in the correct position) all I get is an "unidentified network) in windows 10

    Thanks

    And please, at this stage, no comments re using a separate router! I'll cross that bridge when I get basic functionality!

    read more...
    0 490
    • DennisMilsom
      RexBeckett

      @DennisMilsom 


      The procedure is this:


       


      Connect your PC to the XR's access point. Open XAir-Edit and connect to the XR. Open the Setup -> AP tab. Click the WEP button. Enter the required password in the KEY field. Click APPLY. Exit X-Air Edit. 


       


      Move the XR's network switch to Ethernet and wait ten seconds. Move the switch back to Access Point. You should now be able to connect your PC to the XR's WEP-secured access point. Restart X-Air Edit and connect to the XR.

      • November 11, 2019
    • DennisMilsom
      DennisMilsom

      thanks for the reply!


      At this stage nothing works! I cannot even change the LAN to DHCP it seems to want to stay "fixed" on Static...so All I can do at this stage is connect via open wi-fi using the inbuilt router as nothing and I mean NOTHING else works, or even hints at working.


      And the whole secured thing, nah it just does not seem to "take" - I'll give it one more go and I'll follow to the letter what you wrote!

      • November 11, 2019
    • DennisMilsom
      DennisMilsom

      Brilliant! thanks - I was sure I was doing those steps, but I obviously was missing something. Mebbe not waiting long enough on the delay to go back to AP!


      Now to try and sort the LAN and external router issues - although as it now has a 13 digit password, would I really need to worry about an external router?

      • November 11, 2019
    • DennisMilsom
      RexBeckett


      @DennisMilsom wrote:


      Brilliant! thanks - I was sure I was doing those steps, but I obviously was missing something. Mebbe not waiting long enough on the delay to go back to AP!


      Now to try and sort the LAN and external router issues - although as it now has a 13 digit password, would I really need to worry about an external router?





      @DennisMilsom 


      I'm happy to hear that you are making progress.


      The internal access point is OK for use at home but I recommend that you use an external router for gigs. The internal access point does not cope well in the presence of many smartphones hunting for connections to the internet. It also works only on the 2.4GHz Wifi band which is very congested.


       


      I recommend getting a dual-band router that supports 802.11ac 5GHz Wifi standard, has multiple external antennas and two or more network sockets. The 5GHz Wifi band is less congested and more resistant to interference. Having multiple sockets on the router allows for a local wired connection to a PC or Tablet in case of Wifi problems. High speed is not essential - an AC750, AC1000 or AC1200 router would be fine.

      • November 11, 2019
    • DennisMilsom
      DennisMilsom

      @RexBeckettThanks - I am having issues getting even my existing spare (2.4) router working over the LAN. It is at the moment unsecured and open, but I cannot log in to the settings (to set a password) without it needing a live internet connection! And futher, even with it at open security, the XR refuses to see the LAN connection. I tried the longer wait time before flicking back to LAN as well! So the way I am thinking is that at least the internal has some sort of protection and that if the external has no protection then it is not better at all really??


      As for smartphones searching, I read that most of these actually ignore secured networks when doing their searching? And if that holds true, then the internal would not get as hammered by "search and connect" requests??


      Please keep in mind I am not trying to disagree at all, just trying to wrap my head the varying opinions on a technology (in live stage work) that is very new to me.

      • November 12, 2019
  • MartinPressmar
    Contributor - Level 2
    2019-10-16

    Hello together,

    as there where already some picture leak.
    When would Behrigner release this version?
    Would be nice to have it on a GIG at the weekend.

    I am happy to be a beta tester even.

    Best regards,
    Martin

    read more...
    0 487
    • MartinPressmar
      AnthonieHunter

      I would never take a new release into a live gig. 
      Enough things can go wrong on a live gig, I don't need a headache because some feature or setting does not perform as expected. 
      I love my X32, but don't like to be suprised by some unexpected behaviour. 
      I welcome any new feature, but will only take it to a live gig after a decent test.

      • October 16, 2019
    • MartinPressmar
      LarryBonare

      I agree with Antonie

      • October 18, 2019
    • MartinPressmar
      Virtue67-

      I look amazing can't wait either here is a video clip.


      https://www.youtube.com/watch?v=wv5f1aO_b1A&t=21s

      • November 6, 2019
  • Pau
    Contributor - Level 2
    2019-12-02

    Hi

    Love my X32s.thanks for an amazing product Behringer. 

    V4.0 looks great, however it doesn't work for me. 

    I have the Utrack X32 card installed and all worked fine before the v4.0 firmware update.

    The audio is now distorting and clipping. Horror... 

    It's also dropping out of record causing wallet and reputation damage.. 

    Others are experiencing this problem also. 

    The desk is now unusable with v4.0 for my purpose and as the previous firmware has been removed from the downloads page I'm now stuffed. 

    Will this issue be addressed on the bug fix v4.01 or do i need to go back to using Yamaha ? 

    Also it would be helpful to assign multiple FX to the mix buss. If this is a possible for your programming guys to look into for V4.01. Just a thought...

     

     

     

     

     

     

     

    read more...
    0 471
    • Pau
      RexBeckett

      @Pau 


      Hi Paul, welcome to the community.


       


      I understand that other users have found that they get distorted recordings using the UTrack X32 card if the recorded level exceeds -12dBFS. Cymatic have recently discontinued this card so they may not be working on revised firmware to solve the problem - although it could be worth asking them.


       


      You can still get V3.12 firmware for the X32 from the downloads page if you check the Show Legacy Versions option.

      • December 1, 2019
    • Pau
      GaryHiggins

      That card is only going to get less and less support from this point on. IF the next firmware fix doesn't solve your issue, I would suggest getting an X-Live card. They can be easily had for $149 and I have seen them as low as $100. They make great live 32 track recordings and will be supported in the future. They are an integral part of the X32/M32 ecosystem.

      • December 1, 2019
    • Pau
      Pau

      Thats a good suggestion.


      I dont think that is the way forward for me though.


      I'm going to stick with the old firmware for now.


      very dissappointing but better than spending more money and f---ing around with cards.


      defeats the object of having it all on hard drive....


       


      I must say that I am more than dissappointed with Cymatic who have not even botherd to respond.


      they happily took my money but are providing no back-up or support.


      I  will NEVER buy anything from Cymatic ever again and I urge everyone else to spread the word how rubish thier after sales are.


       


      Having said that


      I would like to urge Behringer to take into account  individuals such as me who have literally dozens of Behringer devices. We spend an awful lot of money on your products.


      We are the lifeblood of your business and deserve to be looked after and cared for.


      Please do not render equipment incompatible when making firmware revisions. if you acidentily do, please put it right ASAP.


      I had a blow up with Microsoft driver executives about this 10 years ago while releasing thier WIN7os, I angrily let them know that they had cost me a fortune in obsolete periferals and didnt want thier busines any longer unless they put things right. I still havent made a full transition to Apple yet as they made an effort for me.


      Point being:  Behringer, you have a duty of care when you move the goal posts..


      .BTW, Thanks Behringer for your quick email from support. not the result i was hoping for but at least you made the effort.


      Please fix the firmware.


       


        

      • December 2, 2019
    • Pau
      Paul_Vannatto

      Hi Paul @Pau 


      I think you misunderstand that Behringer never supported this product from Cymatic and made it very clear when it was first released. As far as I know there have been very few forum members that actually used the card. Plus whenever there is a firmware upgrade, it is the responsibility of any 3rd party developer (including myself) to upgrade the product to continue to be compatible to the the new firmware. 


       

      • December 2, 2019
    • Pau
      Pau

      No missunderstanding Paul, just trying to get you guys to help pick up the piecies that Cymatic have smashed on the floor. 


      My point is that the previous firmware worked fine so obviously some code has been messed up with V4.0. it will become evident in other insignificant functions over time (perhaps in the file system), It would be nice if it could be considered when the bugs are ironed out in future firmware updates.


      Look everyone, Another example how super quick Behringer are to reply and how shoddy and rotten Cymatic are.


      Please everyone be aware how bad that company is and don't waste time or money on thier products. they obviously couldnt care less..


      if anyone works for Cymatic,, Jump Ship!

      • December 2, 2019
  • Klaus
    Contributor - Level 2
    2020-01-22
    I found my unanswered post in the recording tribe... and repost here... In X32-Edit v2.5, when the channel send configuration is changed in the bus configuration tab, i.e. from post EQ to Subgroup and back, this bus's channel sends ( or channel 'receives' ) are reset to zero, a very handy feature. I can't figure out where this handy feature is accessible ...in X32.Edit v 4 Thanks for letting me know best Klaus
    read more...
    0 463
    • Klaus
      GaryHiggins

      @KlausIf you are meaning firmware 4.0, there were lots of issues with that version. Try 4.02 (or 4.01)

      • January 21, 2020
    • Klaus
      Klaus FW 4.02 Anyone ? THNX Klaus
      • January 21, 2020
    • Klaus
      KevinMaxwell


      @Klaus wrote:

      I found my unanswered post in the recording tribe... and repost here... In X32-Edit v2.5, when the channel send configuration is changed in the bus configuration tab, i.e. from post EQ to Subgroup and back, this bus's channel sends ( or channel 'receives' ) are reset to zero, a very handy feature. I can't figure out where this handy feature is accessible ...in X32.Edit v 4 Thanks for letting me know best Klaus



      I gave someone edit V2.5 so he could learn the console without having the console in front of him, because that 2.5edit looks like the way that the mixer is laid out. And while on the phone with him yesterday I discovered that when changing the input it reset all of the levels to that send all the way down. I didn’t like it but I could see the advantage to it. I just tried that on edit V4.1 that is the second release of the V4 edit software and is meant to be used with consoles updated to V4.??, I don’t know why the slightly different naming standard. There doesn’t seem to be a setting that will automatically reset the faders all the way down when you change the routing in recent versions of edit. I even checked edit V3.1 and it behaves the same way as edit V4.1 does. so they changed this behavior a while ago.

      • January 21, 2020
    • Klaus
      GaryHiggins

      @Klaus Firmware 4.02


      https://www.dropbox.com/s/6j3bfd996ntwnlk/X32_Firmware_4.02.zip?dl=0


       


      or


      https://www.behringer.com/Categories/c/Behringer/Downloads#googtrans(en|en)


       


      EDIT: I have no idea if this firmware does what you want...but that's some links to it anyway.


       

      • January 22, 2020
  • hbc
    Contributor - Level 1
    2019-11-26

    Hey Team,

    So we updated to the v4 firmware last week which we're loving, but noticed a few issues.

    Firstly, it reset my libraries and snippets. I did a backup of everything before I did the update, so I was able to restore them, HOWEVER, when I imported all my libraries, I only had 46 loaded, with the other 53 as blanks. I had spaces between some items so I could "block" content together to break it up a bit. When the 46 items imported, they renumbered themselves to have no gaps in between, but they also wiped the other 53 items, and I can now no longer save items to those 53 slots in the library. If I hit the utility button it shows the other 53 as greyed out and I can't select them at all. How can I get access to these 53 please? Also, it would be super helpful when saving a library item to "insert above" or "insert below" another item so I can re-order my list. For example, I have 6 singers mics all saved alphabetically. Say I want to add another singer whose name starts with "A", I want to be able to go "insert/save above" my singer whose name starts with "B" so it's quick and easy to find it next time. Especially since my spaces have gone.

    The other issues we had was the static IP address reset itself to auto (quick easy fix), some of the icons didn't update relative to each other (e.g. we had the "crowd" icon which on channels swapped to the new singing icon but on the bus changed to another icon completely which I can't remember. Easy fix, but a bit odd).

    Just a quick feature request as well. When recalling a library item, it would be good to be able to load the scribble strip colour seperate to all the other elements. We have colours on our mics and when we call the item it resets to the colour it was when we saved it. I would like to just be able to load the name and the icon if possible.

    read more...
    0 461
    • hbc
      adam_nowak

      Hi hbc


      Thanks for reaching out


      Firmware upgrades do replace the internal memory, so it is unavoidable to have some data loss.
      This will be somehow prevented from this FirmWare 4.00, by asking a user to do a console backup before updating the mixer.


      Concerning libraries and importing presets, the FW 4.00 had problems when importing presets made prior to FW 2.12, this will be corrected in the next release. A temporary workaround would be to use X-Edit to transfer those presets to your mixer. You could also check the preset files using a basic text editor, they should start with "#4.0#". If it starts with a single "#", thats the cause of the problem... You can fix those files by adding the proper starting version number, but using X-Edit will be way faster.

      Regarding the fact that you can no longer save in those slots, it's because you are scrolling the list using the LOAD encoder, this selects only the presets that can be loaded. Try scrolling using the SAVE encoder.
      In this FW 4.00, there are many places where several encoders double the function of other ones. It was a bit of a shame to have useless encoders, and it can somehow save you if you have a faulty encoder.

      For those "Insert preset" feature request, the tricky part would be to fit it in the user interface in an understandable way. For this task, I recommend using X-Edit again. This lets you manage the libraries with more flexibility, as its easier to use your computer screen than the builtin mixer screen.

      The reseting IP adress is normal, as the mixer defaults to DHCP set to ON when doing a factory reset. So this is not a bug
      Icons changed to fit the new design better, they are taken from the channel icons used on the new WING mixer.


      It is possible to recall only the Name/Icon/Color part of a preset by using the recall scope on the left.
      Select the header of the list to (de)select all elements, and check "Name/Icon". Unfortunately, there's no way yet of locking the colors, but we take note of your request


       


      Hope all this helped,
      Musically, Adam

      • November 26, 2019
  • Jojomeurer
    Contributor - Level 1
    2019-11-14

    Since the Update of my X32 Console to Firmware 4.0 the Routing for VST Host Applications isn`t working. Im using LiveProfessor with newest Software Release. When I am patching the Card outs to send the Local Inputs out and selecting the card In at the X32 to the faders there is an output Visible on the meters in LiveProfessor, but there ist no return to the console. 

    Its the same in both patching possibilities. 8-Block Routing and user layer point-to-point patch. When i restore to the 3.12 firmware its working fine with exactly the same settings.

    Maybe a bug in the new firmware?

    read more...
    0 461
    • Jojomeurer
      GaryHiggins

      @Jojomeurer I can't speak to your exact issue but I struggled earlier today with my XTouch and my mixers, I could not connect no matter what I did...I was sure it must be the firmware BUT when I looked at my setup I noticed all my midi settings and (probably) others elsewhere had been set back to something other than what was on my mixer prior to loading up firmware 4.0. I'm not saying this is your issue but you may want to compare your "old" setup against what 4.0 loaded by default. Something on an overlooked page may have been altered. It's perhaps worth a look.

      • November 14, 2019
  • LifeHouse
    Contributor - Level 2
    2019-09-22

    Hello Everyone,

       Looking to get some help, I am recording on my Behringer X32 SD card, I have the X-live Expansion.  Here is my Config... I am coming in AES50, I have audio, its mixed, I record directly to the SD card, I have the settings on Automatic, 32 in 32 out.  When I go to playback, I cant hear anything, I check the routing and everything seems routed correctly (Card 32 in) on each channel accordingly.  I am using a 64 gig Storage card, 3/10.  the screen says its recording, but no playback.  HELP!Screen Shot 2019-09-22 at 7.49.15 AM.pngScreen Shot 2019-09-22 at 7.49.26 AM.pngScreen Shot 2019-09-22 at 7.49.34 AM.png

    read more...
    0 460
    • LifeHouse
      Paul_Vannatto


      @LifeHouse wrote:


      Hello Everyone,


         Looking to get some help, I am recording on my Behringer X32 SD card, I have the X-live Expansion.  Here is my Config... I am coming in AES50, I have audio, its mixed, I record directly to the SD card, I have the settings on Automatic, 32 in 32 out.  When I go to playback, I cant hear anything, I check the routing and everything seems routed correctly (Card 32 in) on each channel accordingly.  I am using a 64 gig Storage card, 3/10.  the screen says its recording, but no playback.  HELP!





      What have you got assigned on the Routing, Card Out screen? It should be the same as on the Routing, home (Input) screen in Record mode.

      • September 22, 2019
    • LifeHouse
      LifeHouse

      I just checked the Card Out and it is assigned Card out 1-8, 9-16, 17-24, 25-32.  Please Note: So im recording from a Midas M32R, im coming out of the Midas via AES50B (So the Internal Sync is AES50B in setup under synchronization on the X32.  Coming INTO the Behringer X32 Im getting all of the 32 channels and when I hit record on the setup tab the wheels start turning as though its recording on the X32.  when I go to play back do I need to change the Syncronization? or anything Im Missing?      

      • September 22, 2019
    • LifeHouse
      Paul_Vannatto


      @LifeHouse wrote:


      I just checked the Card Out and it is assigned Card out 1-8, 9-16, 17-24, 25-32.    





      That means that you have assigned the Card IN signals to the Card Out. In other words you are recording a bunch of blank tracks. If you want to record the same thing that you have assigned to the X32 inputs, copy those assignments (Routing, home (Inputs), recording mode) to the Card Out screen.


       

      • September 22, 2019
    • LifeHouse
      LifeHouse

      When I Record, my home inputs are set to AES50B 1-8, 9-16, -17-24, 25-32. 


      Do outputs need to be set to anything particular?


       


      When I Playback they are set to Card in 1-8, 9-16, 17-24, -25-32.  still dont see anything registering...  When im recording I do... but when i go to playback its not.  When I playback should the synchronization be different?

      • September 22, 2019
    • LifeHouse
      Paul_Vannatto


      @LifeHouse wrote:


      When I Record, my home inputs are set to AES50B 1-8, 9-16, -17-24, 25-32. 





      Then on the Routing, Card out, assign the following:


      * Outputs 1-8 -> AES50 B1-8


      * Outputs 9-16 -> AES50 B9-16


      * Outputs 17-24 -> AES50 B17-24


      * Outputs 25-32 -> AES50 B25-32


      Then re-record your gig.

      • September 22, 2019
  • bcrooms
    Contributor - Level 2
    2019-08-07

    I know there are similar threads on here about USB playback, but I don't believe I've come across one addresing what I am looking to do if its possible at all.

    I am able to playback a stereo return from my DAW (Presonus Studio One 4) over the ultranet to P16 modules...

    What I am really wanting is to multi track playback from the DAW, having all 16 channels independent in the USB return playback from what was just recorded in the DAW for listen back for the full band via the P16 modules and not have to listen back just on stereo.

    If that scenario isn't possible with the XR18, I can deal with it, but it would be nice. 

    Any help is appreciated.

    -Brandon

     

     

    read more...
    0 450
    • bcrooms
      RexBeckett

      @bcrooms 


      Hi Brandon, welcome to the forum.


       


      Yes you can do this. If you are running Windows on your PC, you need to install the ASIO drivers for the XR18. Then set your XR18 into 18/18 ch mode on Setup -> Audio/Midi. You should then be able to route your DAW tracks to the USB outputs. You may need to select the ASIO device in your DAW preferences.


       


      To send the USB returns to Ultranet, open In/Out -> Ultranet and scroll to the right to select the USB Return channel for each Ultranet output. There is a preset button USB Return that selects the first 16 USB returns.


       

      • August 7, 2019
    • bcrooms
      bcrooms

      I do have the ASIO drivers for the XR18 installed on my Windows PC...but I can't seem to get this to work properly. 

      • August 7, 2019
    • bcrooms
      RexBeckett


      @bcrooms wrote:


      I do have the ASIO drivers for the XR18 installed on my Windows PC...but I can't seem to get this to work properly. 





      Did you make the other settings I mentioned? In what way does it not work?

      • August 7, 2019
    • bcrooms
      KenMitchell

      Hi @bcrooms , 


       


      In Studio One, you also have to set each track output to the corresponding USB Return going to the mixer.  Optionally, you can remove the tracks from the Master Buss or you can just mute it when you only want to send the individual tracks.  I don't use Studio One but I'll see if I can give you some guidance on setting the track outputs to the USB Returns. I think I have the free version somewhere. 


       


      Hope this helps, 


      Ken


       

      • August 7, 2019
    • bcrooms
      bcrooms

      I tried again to set the outputs in Studio One to relate to each channel return, but it still will not return audio through the ultranet interface to my P16s.

      • August 15, 2019
  • Virtue67-
    Regular Contributor - Level 1
    2019-10-03

    Where can we obtain additionally preset? Yamaha TR range has a nice range with even Mic and equipment preset which you cal dial-in.

    0 449
    • Virtue67-
      Vasco_Romijn

      There are no (official) additional presets for the X/M32 mixers. You can use the presets already in, tune them to you're needs and save them as new preset. Maybe there are users who already made there own (tuned) presets and wanna share them with you.


      I do not use presets on any mixer because they never sound as what I like. I tune everything on my experiance.

      • October 3, 2019
    • Virtue67-
      Paul_Vannatto


      @Virtue67- wrote:


      Where can we obtain additionally preset? Yamaha TR range has a nice range with even Mic and equipment preset which you cal dial-in.





      Attached is the Artists Presets package that was included with the X32 firmware 2.0


       

      X32 V2 Presets.zip
      • October 3, 2019
    • Virtue67-
      Paul_Vannatto

      Attached is a compilation that one of the forum members put together for the X-Air family of consoles. Since the X-Air and X32/M32 share the same effects engine, these will also work with the X32/M32


       

      XR Mixer Series Presets.zip
      • October 3, 2019
    • Virtue67-
      Virtue67-

      Thank for the presets, I looked at them Will use most of them THANK YOU SO MUCH.


      If I plug a say GTR quickly loads a preset so it has to go quickly on live gig scenario. This is where Presets come in handy Because Unlike analog, digital mixers are not as quick to set up analog eq with digital is but more fiddle you can't do it in a few seconds basically.


       

      • October 13, 2019
    • Virtue67-
      Vasco_Romijn


      @Virtue67- wrote:


      If I plug a say GTR quickly loads a preset so it has to go quickly on live gig scenario. This is where Presets come in handy Because Unlike analog, digital mixers are not as quick to set up analog eq with digital is but more fiddle you can't do it in a few seconds basically.


      Every instrument/voice sounds different and need adjustments, presets are good startpoints but nothing more than that is my opninion. Also a digital mixer can be setup quickly, it is just all about nowing you're gear. We did a festival with different bands a couple of weeks ago with a M32 and we do soundchecks in 5 minutes.




      • October 14, 2019
Go to page