Statistics

165,441 members
196 posts
  • Bigdutch
    Contributor - Level 1
    2019-12-01

    Hi

    What about I nice retro sampling keyboard with some modern additions- no such thing nowdays.

    1 39
  • wftlrd
    Contributor - Level 3
    2020-02-06

    post your feature requests here.

     

    • din sync24 in
    • when in midi sync mode midi note in (and pitchbend) changes key of pattern
    • synthtool sequence editor; transpose, randomiser, brush tool, copy and paste notes, add accent with key+mouseclick
    read more...
    2 80
  • Thanasis
    Contributor - Level 1
    2020-05-27

    Hello, new neutron user here.
    When I crank up the resonance to 3 o'clock and above and do a filter sweep, I hear distortion coming from the overdrive cirquit ,even if the drive knob is fully closed. The only way to clean the signal ,is to put the overdrive level past 10 o 'clock but then the output signal becomes too weak to drive the preamp ,causing unwanted noise .
    Is there any calibration that I can do to overcome this issue?
    Even my MS20 filters are cleaner in full resonance sweeps.
    Thanks.

    read more...
    0 30
  • Swisstony10
    Contributor - Level 1
    2020-04-01

    Just integrated a TD-3 into my studio, and I'm loving it so far, except for one minor issue.  I can't seem to control anything about it from Cubase.  It's taking midi sync perfectly happily, over USB, but all I can do is start/stop it with the transport controls.

    What I really need to be able to do is to send pattern change information during a project to switch patterns, and also send start/stop signals to it via midi. At the moment I can just have it playing all the time throughout the project.  The midi implementation table in the user guide that came with it isn't terribly useful in helping me work out which controls I need to send it from Cubase to do start/stop and switch patterns.  Any advice gratefully received! 

    read more...
    0 50
  • riffjam
    Contributor - Level 2
    2019-06-21

    A ( 3 ) x 3340 VCO, ( 3 ) x LFO version of the "Crave"? CAST your VOTE in my "Crave 3" Synth Poll!  How about a full-featured workstation keyboard small enough to carry in a gig-bag and play anywhere? Or how about a "live performance" synth that allows you to tweak 27-synth parameters simultaneously from one hand as your other plays the keyboard? These are just a few of my crazy synth design ideas. Would you like to see Behringer produce any of these? Take a look:  Tomm's Crazy Synth Designs

    read more...
    0 200
    • riffjam
      TC-Mike

      Hi Tommy,


      thanks for your input.


      is your Crave 3 idea meant to be a monosynth too?


      What filter should it have ? the same as the Crave ( Moog ladder) or a different one eg the multimode filter from the Neutron?


      i think i'd keep the sequencer rather if it is meant to be a 3 osc mono


      From your other design drafts i like the idea of a sample based portable "workstation" kind of keyboard- an updated Rompler design loaded with high quality bread and butter sounds , enough voices and maybe an analog filter to round it all off


      best regards,


      Mike


       


       


       


       

      • June 24, 2019
  • Oskoskosk88
    Contributor - Level 1
    2019-09-13

    Hi! I´m a guitarist who just ordered the Behringer K-2. What keys can I connect to it? I have a Komplete Kontrol A49, will this work?

     

     

    Thanks!

    Osk 

    0 105
  • synthman2017
    Contributor - Level 1
    2019-10-19

    Hi all. Help!I literally just purchased a brand new Odyssey and for some unknown reason a note is permanently on. I can't stop it and the ADSR has no effect. Is it possible that the synth is in some test mode?

    0 213
    • synthman2017
      Talos

      Make sure your VCA GAIN slider is fully down, it confuses a lot of people who think you need to turn the amplifier up to hear it especially with the lack of a dedicated volume knob, but that is taken care of by the AR /ADSR slider.

      • October 19, 2019
  • Hans-Georg
    Contributor - Level 2
    2019-12-30

    Hi All,

    Does anyone knows, how the COPY, PASTE buttons work on the TD-3?

    I appreciate your reply.

    Kind Regrads
    Hans

    0 430
    • Hans-Georg
      marco_m_berlin

      1.Mode: Write


      2.Function:normal mode


      3.select source pattern


      4.while  pressing FUNCTION Button  press ( 1.copy 2.destination pattern 3. paste)


      5. release FUNCTION button


      6.be happy


      Grüße, Marco


       

      • January 8, 2020
  • 3phase
    Contributor - Level 2
    2019-12-18

    Its not possible to create care tickets..there is no place to report bugs..

    So how can we hope for bugs to be fixed? 

    Is it better to return the synths to the seller?

    2 55
  • matthewling
    Contributor - Level 1
    2020-05-10

    Hi everyone, has anyone been able to raise a support ticket on the Behringer care portal? I keep getting mandatory fields that are not available for entry which means I cannot submit a ticket.

    Thanks, M

    0 172
    • matthewling
      RexBeckett

      @matthewling 


      Hello Matthew, welcome to the community.


       


      There have been other reports of recent problems with the Care ticket system. I shall ask @AlexLane if he can investigate.

      • May 10, 2020
    • matthewling
      AlexLane

      Thanks, @RexBeckett 

      Hi @matthewling ,


       


      I have reported the issues to the dev team, hopefully this will be solved today. They are looking into it now.


      I did some testing and some forms are coming back with errors, I noticed one thing on the drop down menu issue. Once I choose brand, it sometimes takes a little time before the drop down menu loads. Might be worth trying again and giving it a little time for the menu to load.

      I will report this problem too, hopefully it can be made faster.

      • May 10, 2020
Go to page