Statistics

165,363 members
41 posts
  • TONKLA
    Contributor - Level 1
    2020-02-19

    I bought a pair of Nekkst K6 (Brand new) and found that 1 piece has two defection spot on a subwoofer.

    Could I claim this piece of speaker with a Distributor in my country ?

    41238.jpg
    read more...
    0 31
  • AyChords
    Contributor - Level 3
    2019-11-10

    I bought a subwoofer THRUTH B2029A (fairly used) on eBay, and after carefully reading the manual and following the voltage selection procedures, I powered on the subwoofer. After awhile (5min) I discovered the woofer was seriously heating, and shut down after some minutes. I thought it was disconnected from the mains but not. I troubleshoot (checked and replaced the fuse) but it was not coming up.
    Later I discovered the toroidal transformer is faulty.
    Now I want to replace the transformer, what’s the specifications I should be looking for.? And what’s the voltage that enters to the PCB of B2029A?

    read more...
    0 199
  • colino_ltapl
    Contributor - Level 2
    2020-02-19

    Hi guys, 

    I have a question and i hope we all can learn from each another. 

    Recently i have updated the firmware of the DP48 to 1.2, after which i am not able to remote control the other units via the 1st unit. 

    Is there a minimum unit to setup in order to do remote control of the other unit? Or is there a special CAT5 Cables we should be using in order for the connectivitiy to get thru. 
    Please take note that all my 5 units has signals passing thru from the M32 Console. 

    Hope to hear from you guys.

    Cheers!

    read more...
    0 169
    • colino_ltapl
      Paul_Vannatto


      @colino_ltapl wrote:


      Recently i have updated the firmware of the DP48 to 1.2, after which i am not able to remote control the other units via the 1st unit. 





      Are you trying to change the group names and assignments from the first DP48 or from the M32? If it is from the first DP48 (in the chain), do you have it set  with the remote on (its device ID should say MSTR) and the rest should have remote on and should have unique device ID. Once that is setup, on the master (first) DP48, goto the Broadcast line and press the encoder. 


       


      If you are trying to send from the M32 Library, AES50 screen, we found a bug which the fix will be part of the next release.


       

      • February 19, 2020
    • colino_ltapl
      colino_ltapl

      Hi Paul,


      Appreciate your replies. 


      just to recap, the first DP48 on master and the rest are on their on IDs, after which punch in the broadcast on the first unit and select the other unit ID to control them correct? 


      Unfortunately it doesn't seems to be working. Did i miss out any step?

      • February 19, 2020
    • colino_ltapl
      Paul_Vannatto


      @colino_ltapl wrote:


      Unfortunately it doesn't seems to be working. Did i miss out any step?





      Did you turn on Remote on all the DP48's before pushing the Broadcast?

      • February 19, 2020
  • dhpatel
    Newcomer - Level 3
    2020-09-08

    testt testt

    1 8
  • shiyah
    Contributor - Level 1
    2019-06-04
    0 201
  • staceyhainey
    Contributor - Level 3
    2019-06-07

    Just a general question,,,,

    My band just purchased an M32C with the DL32, and PM16’s for monitoring 

    i split the vocal, and instruments into mix busses, and sent the busses to ultra net, but it seems like we aren’t getting the full signal (some busses seem absent on the pm16)   We do have something that kind of works, but there’s gotta be a better way 

    will post a screen shot of the routing pages

    read more...
    0 285
    • staceyhainey
    • staceyhainey
      RexBeckett


      @staceyhainey wrote:


      Just a general question,,,,


      My band just purchased an M32C with the DL32, and PM16’s for monitoring 


      i split the vocal, and instruments into mix busses, and sent the busses to ultra net, but it seems like we aren’t getting the full signal (some busses seem absent on the pm16)   We do have something that kind of works, but there’s gotta be a better way  


      will post a screen shot of the routing pages





      @staceyhainey 


      Where are you connecting the P16Ms - to the M32C or the DL32? If the DL32, you need to open Routing -> AES50 A/B and select AES50-A 33-40 = Ultranet 1-8 and  AES50-A 41-48 = Ultranet 9-16. This will send the 16 Ultranet outputs to the DL32 on AES50-A 33-48 which are routed to the P16 socket.  


       

      • June 7, 2019
  • EllisLampman
    Contributor - Level 3
    2020-05-29

    Does running IEM (earbuds) like Westones out of the HA8000 work well? Obviously a 1/4" to 3.5mm adapter is needed, but I'm more concerned with the impedence working with earbuds as opposed to headphones.

    The 1/4" phone jack out of my Mimic Pro drum module sounds terrible with my IEMs, so I think thats an impedance issue with it being designed for over-the-ear headphones.

    Anybody know about this?

    Thanks

    read more...
    0 39
    • EllisLampman
      RexBeckett

      @EllisLampman 


      Westone IEMs usually have an impedance of 19 Ohms. The HA8000 V2 can drive headphones with impedance as low as 8 Ohms so should be fine. The combination of Westone's high sensitivity with the high output level of the HA8000 could make them very loud. Be careful with the level controls!

      • May 29, 2020
  • QATestAccount
    Newcomer - Level 1
    2020-07-21

    Test PNG

    0 35
  • marianorusso
    Contributor - Level 1
    2019-11-22

    I need to activate warranty support (as required by your Support Request Response (Case: 01.032.712)
       communicating: • current postal address (including City / Postcode / Country) via gabriele jannelli 23 80129 napoli italy
    • Serial number of your item (foto)
    • Proof of purchase * enquire  pdf
    to obtain RMA number and service center.
      do you give me instructions?

    [email protected]
    serial mixer beringer.jfif

    fattura beringher mixer.pdf
    read more...
    0 110
    • marianorusso
      GaryHiggins

      @marianorusso They have stopped putting date code stickers on a lot (if not all) of their products. Your date code would by March 2018 which is the first 4 digits after the S in the serial number.

      • November 21, 2019
  • QATestAccount
    Newcomer - Level 1
    2020-07-21
Go to page