Statistics

165,441 members
196 posts
  • MaxKoepke
    Contributor - Level 1
    2020-01-25

    Hi,

    My out of warranty xr 12 shuts down after an hour.  Repair shop said $275 plus shipping to repair so I just got a new one.  I want to transfer a snapshot of the set up to my new unit via USB (or any method).  Is this possible?

    read more...
    0 63
    • MaxKoepke
      RexBeckett

      @MaxKoepke 


      Hello Max, welcome to the community.


       


      The XR12 does not have any way to save snapshots to a USB stick. You can save the settings using XAir Edit on a PC or Mac though.


       


      Load each stored snapshot on the XR12, click the Save button (top right) and select Save as Scene. Navigate to a suitable folder, name the scene and click the Save button. Repeat for each stored snapshot. 


       


      On your new XR12, perform the opposite procedure: Load each scene and save the snapshot. 


       


      Note that most, but not all, mixer settings are stored in snapshots and scenes. There are few global parameters like network settings and sample rate that must be set manually.

      • January 25, 2020
  • GaryHiggins
    Superhero - Level 1
    2020-02-04

    What does the "main bus link" on and off do in the wing set up section? If it can link bus faders (or main faders) I cant see where or how it does so or an option to choose which ch faders to link....I'm hoping for an option in there similar to "M/C depends on Main L/R" on the X32. If it does something else, what is it- not enabled in the firmware?

    read more...
    0 178
    • GaryHiggins
      Paul_Vannatto

      Hey Gary @GaryHiggins , I'm not exactly sure how that feature works (if it does work). In the meantime, you can get the same results of the M/C follows Main LR using a DCA. Just tag the FOH Main and the sub Main (or bus) with a DCA tag, then assign that DCA to a channel strip.


       

      • February 3, 2020
    • GaryHiggins
      Roblof

      @GaryHiggins , linking will link main2-4 to main1. Just like m/c on the x32. There is currently no way to select fewer members to link.

      • February 6, 2020
    • GaryHiggins
      GaryHiggins

      @Roblof So does it work yet? The physical faders don’t link/move or is it virtual? I will be at the mixer later today 

      • February 6, 2020
  • AdrianWirth
    Contributor - Level 2
    2020-03-03

    X-Air12, Mixing Station Pro
    If I create a scene or snapshot to a new slot with a new name it overwrites the original scene/snapshot. Saving a new scene also overwrites the snapshot and vice-versa. This makes no sense so I assume I'm missing something.

    read more...
    0 72
    • AdrianWirth
      Paul_Vannatto

      Hi Adrian @AdrianWirth ,


      In all the years I've used Mixing Station (since 2013) with either X32 or X-Air, I've never used it to save scenes/snapshots. I've always used the editor (X32-Edit or X-Air-Edit) to do scene management. Mixing Station works best as a mixing app.


       

      • March 3, 2020
  • straina
    Contributor - Level 1
    2019-10-13
    I record to the thumb drive and it plays back thru XR 16 LR Mains nice, clear, and loud but when I play the thumb drive thru my laptop the gain is very very low. All volume settings in laptop are full tilt. Any ideas? Ive tried diff thumb drive.
    0 77
    • straina
      RexBeckett

      @straina 


      Hi Sam, welcome to the community.


       


      Make sure that the USB recorder source is set to a pre-fader signal tap. This will give a higher recorded level than a post-fader tap if the fader is below 0dB. If the recorded level is still too low, you may need to raise the channel gains to give a better gain structure.


       


      Try setting the channel gains so that, during perforance, the input meters peak at between -18 and -12dBFS. Set the channel faders so that the Main LR mix output peaks at around -12 to -6dBFS with the Main LR fader at 0dB. Adjust your power amplifier gains so that you have the required live volume. You could lower the Main LR fader if necessary but don't raise it above 0dB. Recording from Main LR (pre-fader) should give a reasonable level for playback on a PC. 

      • October 13, 2019
  • earcondition
    Regular Contributor - Level 1
    2020-02-26

    Hi All, is there already a possibillity to connect a WING to a Dante Network ?

    0 96
    • earcondition
      DeclanSlater

      That new "internal" Dante card has not yet been released, guessing it'll be quite some time for that to be on the market.


      It would be possible to use another X32 console with a Dante card right now though, and link it to the wing over AES50.  That's what I'm planning to do for a week long production that I have next month anyway.

      • February 26, 2020
  • artemyradionovi
    Contributor - Level 1
    2020-02-28

    The question is kinda simple, but weird. Can I record a 2-track "summ" to USB stick AND 32 channels of multitrack recording into my DAW simultaneously with Behringer X32?

    Thanks everyone in advance!

    0 113
  • simonc
    Contributor - Level 1
    2019-12-01

    whent to connect my ipad last night to x18 via a wirless router as per every other gig, noticed that the desk did not appear in window but ip address did clicked to connect and the app just shuts down ,anyone else having similar issues? worked fine via laptop set up the same way

    read more...
    0 207
    • simonc
      DavidFin

      They just released an update to the iPad app, that should address this problem.
      Update your app, and try again.
      Problem turned up when iOS was updated to 13.

      • December 1, 2019
    • simonc
      KenMitchell

      @simonc 


       


      The recent update had nothing to do with connectivity. It was to fix the crashes that occured when trying to use the channel controls on an iPad with IOS13.   Not finding the mixer is strange.  The way the app works is it sends out a broadcast /xinfo OSC command and waits for any mixers to reply.  Do you happen to be running IOS9 or IOS10 on your iPad?  There's been reported crashes with those after the latest fix although I don't know the details of those crashes. 


       


      Ken

      • December 2, 2019
    • simonc
      simonc

      Running iOS 10.3.4 as soon as you try to connect or enter demo mode the app shuts down , only since the update

      • December 2, 2019
    • simonc
      maddysman

      When I tried to re-install the app under system 9, it is no longer suitable for my ipad. Guess I'm going shopping before the next gig.

      • December 4, 2019
    • simonc
      KenMitchell

      Wow. I'm stunned.  Their fix is to now require IOS 12 or later. 

      • December 4, 2019
  • alphabravo676
    Contributor - Level 2
    2020-04-24

    Hey everyone,

    (Noob to audio, etc)

    I recently got the Behringer Q502USB and the Audio Technica AT2020 condenser mic. I plugged it all in and it all works, however, there are constant buzzing and static noises when listening to the audio both through the PC and the mixer phones. I have heard (obviously after I purchased it *sadface*) the mixer doesn’t have enough phantom power for this mic as it requires 48V. When I play around with the gain, level, and main mix knobs, the buzzing and static gets louder and quieter, depending on how high or low they are set to. The only way I could get the buzzing to almost disappear was through completely turning off the gain and having the level at just above the lowest. Would the phantom power be the problem here?

    Thanks

    read more...
    0 91
    • alphabravo676
      RexBeckett

      @alphabravo676 


      Hello Lachlan, welcome to the community.


       


      I would not expect low phantom voltage to cause hum. That sounds more like a problem with the XLR cable from the mic to the mixer. Presumably the noise stops if you unplug the XLR cable from the mixer?


       


      Are you using a laptop or desktop PC? If it's a laptop, does it make any difference if you unplug the charger?

      • April 23, 2020
    • alphabravo676
      alphabravo676

      Thanks for the quick response. Yes, if I do unplug the mic's XLR cable, it does stop the noises. I am using a desktop PC. I have also tried different power sockets


       

      • April 23, 2020
    • alphabravo676
      RexBeckett


      @alphabravo676 wrote:


      Thanks for the quick response. Yes, if I do unplug the mic's XLR cable, it does stop the noises. I am using a desktop PC. I have also tried different power sockets


       





      @alphabravo676 


      There could be a fault in the XLR cable. It would be worth trying a different one. Hum can also result from the lack of a proper ground connection to the mixer. The mixer is not grounded through its power supply but relies on grounding through other equipment - e.g. active monitors connected to the Main Out connectors. 

      • April 23, 2020
    • alphabravo676
      alphabravo676

      Sadly I only just bought the XLR cable and I can't easily get another. When you say proper grounding, how can I do that? 

      • April 23, 2020
    • alphabravo676
      RexBeckett


      @alphabravo676 wrote:


      Sadly I only just bought the XLR cable and I can't easily get another. When you say proper grounding, how can I do that? 





      @alphabravo676 


      The easiest way to check if this is the problem is to connect the mixer to audio equipment that is grounded through its power cable. Active monitors with built-in power supplies usually work for this. If you don't have this type of equipment and the necessary cables, I don't know what else to suggest.


       


      Do you just need the microphone for recording/streaming? If so, and you still have the chance to return the AT2020 and Q502USB, you may be better served by an AT2020USB as this would connect directly to your PC.

      • April 23, 2020
  • Switchs
    Contributor - Level 1
    2019-10-02

    I don’t understand how to control what channels and which effects go to the monitors.

    0 293
    • Switchs
      DaveMorrison

      Hi @Switchs Screen Shot 2019-10-02 at 12.09.42 PM.pngPush the Bus 1 button shown in the picture. Raise the faders for the channels you want to send to the bus. Push Main LR when you're done and want to resume "normal" mixing.


      By default Bus 1 is routed to Aux out 1; this can be changed.


       

      • October 2, 2019
    • Switchs
      Switchs

      Thanks for your reply, you‘re very kind.


      Howerver, I was refering to the „bus“ that is routed by default to the headphone jack in the front of the unit.


      I understand you can route any bus you want to the jack, but by default, what is being routed to that bus? How do I change the levels for this bus? Are they the same as the main levels?

      • October 2, 2019
  • digitalfade
    Contributor - Level 2
    2019-11-12

    I wanted to post this link over on the Behringer tribe. Anyone have the QX1002USB that might have some advanced knowlege of the PAN on the the Stero inputs. 3/4 , 5/6, 7/8. Does it PAN the input or will it take both the L/R channels and PAN them to the MAIN MIX left side if you only have the LEFT SIDE of the MAIN connected.

     

    read more...
    0 94
    • digitalfade
      RexBeckett

      @digitalfade 


      The stereo input Balance controls will not convert a stereo signal to mono. When set to centre, the left side of the input is sent to the left mix bus and the right side of the input is sent to the right mix bus. When turned fully clockwise, the right side of the input signal is boosted by 3dB and sent to the right mix bus and the left side input signal is cut off. The converse is true when the balance control is turned fully anticlockwise.

      • November 12, 2019
Go to page