Statistics

165,418 members
153 posts
  • Serge7000
    Contributor - Level 1
    2020-05-06

    When will the tannoy gold 8s be back in stock?

    0 26
  • Farsetbelfast
    Contributor - Level 1
    2020-03-10

    Hi guys I'm looking for processor settings for turbosound tq315.

    If it helps I'll be running them passively using a turbosound lms d24 processor. 

    0 91
  • JasonGibson
    Contributor - Level 1
    2020-02-13

    Hi all.  Am a new owner of a IP300.  I plan to get another, plus one or two subs, and am looking at different online purchase options.  Are the European models of Turbosound speakers identical to North American models, apart from the fuse?  i.e., if I bought a European model of the IP300, could I make it North America "ready" simply by changing the T 3.15 A H 250 V fuse to the T 6.3 A H 250 V?  

    read more...
    0 71
  • buskerer
    Contributor - Level 3
    2020-03-14

    Hello to all,

    I've just bought the PPA200 and want to add a monitor speaker to my set-up.

    There is no dedicated output to add a monitor speaker, so I was wondering if a passive or active monitor might run from the headphone output. Would that work?

    Thanks.

    read more...
    0 124
    • buskerer
      RexBeckett

      @buskerer 


      Hello Viv, welcome to the community.


       


      You should be able to run an active monitor from the PPA200 phones output. Some active monitors have 3.5mm stereo Aux inputs so you could connect with a cable like this one. 

      • March 14, 2020
    • buskerer
      buskerer

      Hello Rex,


      Thank you for your swift answer. I thought that might work.


      I've looked at a few active monitors and I'm limited on the amount of power consumption for busking.


      I'm running all my gear from a lithium battery and only a 300watt inverter so a passive monitor would be the ideal solution to keep the power load down. There is a mono direct output and left/right RCA outputs on the PPA200 - would a passive monitor work from either of these do you think?


      I've spent a small fortune (to me) on all the gear I already have otherwise I'd just go with an active monitor and buy a higher wattage output inverter and use the headphones output.


      Again, thank you for your reply.

      • March 14, 2020
    • buskerer
      RexBeckett


      @buskerer wrote:


      Hello Rex,


      Thank you for your swift answer. I thought that might work.


      I've looked at a few active monitors and I'm limited on the amount of power consumption for busking.


      I'm running all my gear from a lithium battery and only a 300watt inverter so a passive monitor would be the ideal solution to keep the power load down. There is a mono direct output and left/right RCA outputs on the PPA200 - would a passive monitor work from either of these do you think?


      I've spent a small fortune (to me) on all the gear I already have otherwise I'd just go with an active monitor and buy a higher wattage output inverter and use the headphones output.


      Again, thank you for your reply.





      @buskerer 


      I'm afraid that a passive monitor will not work from any of those outputs. You could always go for a monitor with its own built-in battery. Something like Samson Expedition Express?

      • March 14, 2020
    • buskerer
      buskerer

      Thanks Rex you've been very helpful.

      • March 14, 2020
    • buskerer
      buskerer

      Just as an update:


      I have a Roland Cube Street I originally intended to use on it's own for busking, but it's sound quality and flexibility leaves a little to be desired in my opinion, which is why I decided on a pa system. The Cube as most probably know can be battery powered so I'll use it as a monitor.


      In case anyone is interested I power my busking set-up with the following:



      This most probably isn't the place to include a list of the gear I intend using for busking but if anyone is interested I will do so in an appropriate place.

      • March 15, 2020
  • JasonChambers
    Contributor - Level 2
    2019-05-20

    I have 2 IQ15's that are less than a year old and really haven't had much use.

    At Saturday's show one of them after being powered on for about 3 minute and without any load shows "over temp" on the display and stops audio output.

     

    Contacted the point of sale and it's a 4-6 week turnaround for repair, which is very disappointing indeed.

     

    Anyone else had this issue?

    read more...
    0 187
  • guitarman_nebr
    Contributor - Level 1
    2019-06-26

    Hey all,

    I have been using the IP2000's for a few months now.   They sound great....until I have to push them for a bit more volume.  I have a small band with pre recorded tracks for Bass and Drums...we sing and play guitar over these tracks.

    I seems there is a general agreement to set everything on the speakers DSP to "0" to use these as a PA speaker with a mixer.   However, it seems there is not a clear explaination as to how much input to use to optimize the output of the speaker.  

    The ouput runs hot and pegs out very quickly...to the point the system will cut out or clip.  I think Turbosound should do a video addressing input and output settings.  On the DSP display it will show the input at two bars and the output quickly goes off the scale.   It is hard to balance these two settings.  

    Does anyone have their own experiences to share?

    read more...
    0 238
  • albertodertycia
    Contributor - Level 1
    2020-01-22

    Hi!

    I need a woofer 5" for the Tannoy Mercury V1i , or your coil.
    model 3121 0208 type 1328

    someone knows where to buy it

    I can't find it anywhere
    thanks

     

     

    read more...
    0 110
  • OldSchool1948
    Contributor - Level 1
    2020-01-01

    I'm looking for a tube integrated amplifier for my Tannoy DC8ti speakers and would like to hear what others are using.  Currently, I have a Herron VTSP-3A (r02) preamp and NAD M22v2 power amp.  

    0 58
    • OldSchool1948
      GrahamH

      Nobody here qualified to answer. Best going to one of the Fan pages on FB for good advice.

      • May 27, 2020
  • brytech
    Contributor - Level 1
    2020-02-12

    Im trying to get a copy of the free Tannoy Activ-Assist software thats used in setting up the Reveal 6D Monitors. I seem to have lost my copy after a machine rebuild and Tannoy no longer have it on their website.

    Many thanks

    Martin

    read more...
    0 87
  • FrankHarlan
    Contributor - Level 2
    2019-10-02

    I can here a signal from the HF driver, but nothing from the LF driver. I have updated the firmware and it did not fix the problem.  Any suggestions?

    0 148
    • FrankHarlan
      Paul_Vannatto


      @FrankHarlan wrote:


      I can here a signal from the HF driver, but nothing from the LF driver. I have updated the firmware and it did not fix the problem.  Any suggestions?





      Hi Frank,


      Welcome to the forum. Have you had a look at the EQ or crossover settings in the DSP? It may have a very high high-pass setting.


       

      • October 2, 2019
    • FrankHarlan
      MatteoBarbaro

      Hi Frank,



      I think that shoud be the connector between the amplifier and the LF speaker, if you don't solve the problem with the suggestions of Paul of course. Remember that iQ loudspeakers are Two way biamp, so you have two amplifier output, one for each way.


      If it's in warranty i suggest you to contact your reseller.



      Regards,



      Matteo

      • October 28, 2019
Go to page