Statistics

165,404 members
133 posts
  • AlRubio_Jr_
    Contributor - Level 2
    2019-05-22

    Hello!
    I have been asked to configure an X32 and S32 to provide the stage with L/R/Mono Subs & 4 Monitor Returns.
    I've been successfully able to get the monitor outputs to appear on the S32's Output jacks 1-4.
    And L/R are appearing on Output jacks 15-16.
    But while I am "metering" a mono signal at the mixer, that signal is not appearing at any of the Output jacks.

    Isn't there a "default" output jack that it should appear at?
    Might there be a step at getting the Mono signal to the S32 that I am overlooking?
    Thank you for any assistance!

    read more...
    0 97
    • AlRubio_Jr_
      DaveMorrison

      @AlRubio_Jr_ 


      Under Routing, select the Output 1-16 tab. Assign the output you want (14?) to MC

      • May 22, 2019
    • AlRubio_Jr_
      AlRubio_Jr_

      Almost certain that we tried doing that, but may have been on the "wrong page" or some such mistake, what with the unfamiliarity pertaining to the S32/AES50 protocols.
      Doing a lot of reading and video watching in the interim - will attempt again tomorrow.
      Thanks so much!

      • May 22, 2019
    • AlRubio_Jr_
      DaveMorrison

      @AlRubio_Jr_ 


      The routing can be a little confusing. The Output 1-16 is an intermediate stage. You have to set it there before the AES50 can "see" it.

      • May 22, 2019
  • NeilMillward
    Contributor - Level 3
    2019-05-23

    Has the x32-q for iphone been discontinued?  It doesn't seem to be in the app store anymore.

     

    I have now got both the x32 compact and full sized desk - is all the software the same?  ie. same firmware, and will my x32-edit work with both?

    read more...
    0 135
    • NeilMillward
      RichardYClark

      Answer to your second part of the question. Yes firmware and X32 Edit common across all versions of the X32 range. 

      • May 22, 2019
    • NeilMillward
      Paul_Vannatto


      @NeilMillward wrote:


      Has the x32-q for iphone been discontinued?  It doesn't seem to be in the app store anymore.


       


      I have now got both the x32 compact and full sized desk - is all the software the same?  ie. same firmware, and will my x32-edit work with both?





      Hi Neil, 


       


      Good to hear from you again. The X32-Q was developed on an older development platform which is no longer supported by the newer iOS. So that is probably why they pulled it from the app store. The M32-Q should still work for both M32 and X32. But the good news is that Mixing Station has now been ported (from android) to iOS and is available on the app store. We all love using Mixing Station Pro - worth checking out.


       


      @RichardYClark answered your second question correctly.


       

      • May 22, 2019
  • GaryHiggins
    Superhero - Level 1
    2019-05-17
    X32 Mixers
    1 370
    • GaryHiggins
      RexBeckett

      @GaryHiggins 


      It is interesting that your post doesn't show on Home -> Updates, Gary. It seems that the Brand forum is  not connected to the rest of the community - or the history from the old forum. That may just make navigation even more difficult. 

      • May 16, 2019
    • GaryHiggins
      GaryHiggins

      @RexBeckett Probably not quite ready for prime time, I also notice no option to edit a post...a function I often need! A step in the right direction maybe. It is also a number of steps (a few too many maybe) to get there but...hey, its a start 


       


      EDIT: Now I can edit!...could not a few hours ago

      • May 16, 2019
    • GaryHiggins
      DaveMorrison

      As I was looking at this post in Rack Mixers https://community.musictribe.com/t5/Rack-Mixers/X-Air-App-Crashing-today-help/m-p/266896#M1 , I realized that the initial post is both at the top and bottom of the thread. How strange.

      • May 17, 2019
    • GaryHiggins
      Kevin

      Hi @RexBeckett Its now connected to the Updates page. Sorry for the delay. Connecting Brand Tribes to Updates was not really part of the initial release for the restructuring but this seems really important to our users so we followed it up

      • May 17, 2019
    • GaryHiggins
      RichardYClark

      The MusicTribe forum is now improved immensely. Working much better now. But still a way to go to be as good as the old one was IMHO. Thanks. 

      • May 17, 2019
  • dapeaceman
    Contributor - Level 1
    2019-05-20

    Anyone know how to put an effect to four different singers?  Say I wanted them all to sound like the chipmunks, how would I put that FX on each of the four singers?

    0 70
  • alienbee
    Contributor - Level 2
    2019-05-17

    Equipment: XR12 . Ehternet
    Went into windows to start a recording session, opened up the  X-Air Edit app, went into start a new snapshot, loaded up one from our list used a while ago, to start up a fresh session. and for a second or so I went to grab my coffee behind me and turn back around and the app was gone off the desktop. I went to fire it back up thinking maybe I closed it by accedent, so I went to load it again, dubble clicked the icon, and it closed before I could see anything, tried it again, same thing. grabed my ipad, switched to "Access Point" - went right in. everything looked normal..so I went and did "initialize mixer" to see if i can kick start the app back to working. turned it back to Ethernet after restarting the mixer..went to windows and clicked app to start and..nothing..same behavior. closed before anything showed on the screen. 

    ok so..i have a linux manjaro box on the same system..went into that, used the app for linux and it fired right [email protected][email protected] ..
    went to snapshots and clicked the same template to start a session as we did before..(used this a few times before to start sessions). so the app closed down in linux too.. and i couldnt restart it just like in windows.

    went and downloaded the app again for linux and windows...treid fresh apps on both. same crash..
    pushed the pin to rest the XR12 for 2 seconds...and for 10, as mentioned int the manual..
    windows and linux apps dont load..
    but im able to load in with "Access Point" using my ipad.
    ??
    what in the hell is going on?
    anyone can help?

     

    read more...
    0 362
    • alienbee
      alienbee odd thing is ..i used to be able to open the app when the mixer was off too.. not able to even start it when its off now..in linux and windwos
      • May 17, 2019
    • alienbee
      alienbee I went and enabled view of hidden files in my Linux box, and found a folder with X-Air stuff. Deleted all the files, and NOW the App works again for Linux!!

      going now to hunt for the folder inside of windows.



      • May 17, 2019
    • alienbee
      alienbee

      Ok found a fix!
      Windows 10  (replace "folder" for your own user name for that folder)


      C:\Users\"folder"\AppData\Roaming\X-AIR-Edit


      I deleted all files here
      "
      X-AIREdit.init
      X-AIREdit.keys
      "
      restarted App

      all fixed

      • May 17, 2019
    • alienbee
      RexBeckett

      Hi @alienbee , welcome to the community.


       


      As you have discovered, it is possible for a bad setting in X-AIREdit.init to cause XAir Edit to crash - even when used offline. It is interesting that your Linux system caught the same problem. That suggests it must have been triggered by something in the XR12 settings. Perhaps the snapshot you loaded has got corrupted and should be deleted or replaced.


       


      Thanks for sharing your solution.

      • May 17, 2019
  • NigelJaDee
    Contributor - Level 2
    2017-08-30
    All,

    I do live game streams and need a very crisp sound.

    I need to mix in 3 PCs and at least a 1 phone and 1 Ipad device.

    I have an XLR mic that will need to utilize a Roland VT-3 as well.

    I have read that AUX channels 17/18 are the stereo channels for connecting PCs. Is there a way to transform channels 15/16 into the same setup at 17/18 were it is one solo stereo channel? Sames with 13/14 and 11/12 and so on?

    The best way i have been able to do it is stereo link but when using compression its not uniform between the channels and treats them as two channels vs 1 channel. Same goes for AUTO mix which then causes a very weird Wobble effect because it will compress the left when it is softer than right to much vs treating them as 1 single channel like aux does for 17/18.

    I hope that i am clear.
    read more...
    0 897
    • NigelJaDee
      FelixHomann Take a look at your Link Preferences. In the desktop applications yoou ou can find the Link Prefs in "Setup->Audio/Midi". Make sure to check all 4 check boxes. Then linking channels should work as expected.
      • August 30, 2017
    • NigelJaDee
      NigelJaDee

      Felix Homann;130496 wrote:

      Take a look at your Link Preferences. In the desktop applications yoou ou can find the Link Prefs in "Setup->Audio/Midi". Make sure to check all 4 check boxes. Then linking channels should work as expected.




      Awesome so i was doing the link correctly it appears.



      That said, the automix feature still treats the stereo channels solo from one another when auto compressing. Meaning it will compress the left channel if the right channel gets louder 15 compressed 16 open even in stereo link. Basically the stereo link is competing with itself instead of acting as one. Is this intended or a bug that will need fixed?
      • August 30, 2017
    • NigelJaDee
      Paul_Vannatto Hi Nigel,



      Welcome to the forum. I think you are misunderstanding the automix feature. It functions in a similar manner as the Dugan Automix devices that were used for panel discussions, etc. (https://en.wikipedia.org/wiki/Automixer). I don't think it fits your application and it won't work with linked paired channels.
      • August 30, 2017
    • NigelJaDee
      NigelJaDee

      Paul Vannatto;130499 wrote:

      Hi Nigel,



      Welcome to the forum. I think you are misunderstanding the automix feature. It functions in a similar manner as the Dugan Automix devices that were used for panel discussions, etc. (https://en.wikipedia.org/wiki/Automixer). I don't think it fits your application and it won't work with linked paired channels.




      Thank you for the clarification and the warm welcome.



      I guess i could do the same thing but using ducking and side chain the channels i need reduced to the mic.



      The reason the auto mix almost works perfectly for what I'm going for is i was able to allow my friends talking over voip (almost like a second mic) to talk and also duck the other channels as could I.



      Maybe I'm looking at this the wrong way and need guidance as I'm new to live mixing and maybe ducking isn't the answer.



      For the example below how would i get this to work in a manner to make everything sound crisp and clear and still have everything live going out right at or close to 0.



      Channel 1 - Mic

      Channel 2 - VOIP

      Channel 3 - Guest Mic 1

      Channel 4 - Guest Mic 2



      Channel 15/16 - Computer 1 Stereo - Game Audio

      Channel 13/14 - Computer 2 Stereo - Misc Sounds and Audible alerts

      Channel 11/12 - Computer 3 Stereo - Dedicated Music
      • August 30, 2017
    • NigelJaDee
      Paul_Vannatto Hmm... a very good question Nigel. If it was me, I would apply the automixing to the mic channels (ch 1-4), but also send those to a mixbus. Then setup ducking of the stereo channels to be triggererd by that mixbus.
      • August 30, 2017
  • KingBurton
    Contributor - Level 2
    2017-08-12
    Hi everybody.

    Current
    Using electronic drum kit. Only L & R output so we pan hard L/R with low sounds one sire high sounds other.

    Goal
    But drum processor does have midi out. Is there a way to separate each drum to discreet channel through midi at DL16 to M32.

    If yes, how do I make that happen? Asking for three churches.

    Cheers.
    King
    read more...
    0 572
    • KingBurton
      KevinMaxwell

      King Burton;129333 wrote:

      Hi everybody.



      Current

      Using electronic drum kit. Only L & R output so we pan hard L/R with low sounds one sire high sounds other.



      Goal

      But drum processor does have midi out. Is there a way to separate each drum to discreet channel through midi at DL16 to M32.



      If yes, how do I make that happen? Asking for three churches.



      Cheers.

      King




      I think you will find that the Midi outs on the Drums are control outputs. If you wanted to hit a drum and have it bring up or down a fader on the console then that might sort of work. But the Midi out is not a way to get the different drum sounds out of the drums to the mixer.
      • August 12, 2017
  • RejeanDoyon
    Contributor - Level 2
    2015-04-02
    Hello. I use a lot of virtual instruments in my computer (Kontakt 5, pianos, etc) I have test the X-32 rack with my USB connection. It's not very stable: rythm problem, some sounds don't play even with high buffer settings. Is the FireWire connection will be more stable and reliable with my setup ?
    read more...
    0 1,649
    • RejeanDoyon
      FlorianGerstenl Rythm problems shouldn't be affected by th X32.

      Which program do you use as host? What's your audio, and your MIDI clock source?
      • April 2, 2015
    • RejeanDoyon
      RejeanDoyon I use Cubase 6.5 with Windows 7 64 bit. It's X-32 internal clock internal clock. I have compare side by side with a RME fireface UFX (FireWire connection). When a lot of virtual instruments are use, the RME is very smooth an stable. On the X-32, some missing or delayed parts and some audio sparks.
      • April 2, 2015
    • RejeanDoyon
      FlorianGerstenl Maybe you should change the ASIO buffer setting. It's possible that the standard setting of the X32 is much smaller. This leads to higher CPU load and the problems you described.
      • April 2, 2015
    • RejeanDoyon
      RejeanDoyon Yes, i have try this. I have try all combinations. Standard asio settings with 1024 buffer is the most stable.
      • April 2, 2015
    • RejeanDoyon
      Roblof Have you tried setting the clock to card instead of internal?



      I've not experienced the type of problem you have. Do you have some more intel to share?
      • April 2, 2015
  • InactiveUser
    Contributor - Level 2
    2012-08-29
    Hi:
    I just bought the Berhringer X32 and have been trying to connect Waves Multirack software via USB to the XUF FireWire/USB audio interface card. My hopes are to be able to run all the audio inputs during live performance through the Multirack software and back into the X32. I have had some success but have not yet found a "routing" combination that has completely worked. Has anyone tried and done this successfully??
    I am new the forum and would appreciate any thoughts.
    Best,
    Hoyt
    read more...
    0 11,460
    • InactiveUser
      InactiveUser I don't own a X32 yet but I have contacted Behringer and Waves about this and both said it would work. I would contact Waves becuase they were willing to walk me through it. If you e-mail them they will contact you back fast. They have the best customer service I have found anywhere.
      • August 30, 2012
    • InactiveUser
      InactiveUser Thanks, Yes I have spoken Waves and they do not know. No one at Sweetwater or Guitar Center in LA knows the answer either. I just got my mixer and I am having success with adding only 4 channels of AUX 1-4 which is only one of the inputs directly into the onboard audio card. I am trying other combinations to see if I can come up with another combination of routing that will allow me more Wave channels. I will let you know what I find.



      Thanks,

      Hoyt
      • August 30, 2012
    • InactiveUser
      ChristianBoche Hi,

      by now it is a bit clumsy, because the daw returns are not useable as digital inserts on all channel without sacrifying the micpres. You can use the Aux inptus though. Behringer R&D is working on a solution as we speak, this routing option will come in a future firmware update. I'm also waiting on this, we just need a bit more patience.

      Christian
      • August 30, 2012
    • InactiveUser
      OzzyStone

      Christian Boche;480 wrote:

      Hi,

      by now it is a bit clumsy, because the daw returns are not useable as digital inserts on all channel without sacrifying the micpres. You can use the Aux inptus though. Behringer R&D is working on a solution as we speak, this routing option will come in a future firmware update. I'm also waiting on this, we just need a bit more patience.

      Christian




      hi any idea if there is a workaround this?

      I use multirack on every show with my personus

      I want to buy a X32 and will hate to use my plugins
      • January 12, 2013
    • InactiveUser
      PerSovik

      hyeatman;467 wrote:

      Hi:

      I just bought the Berhringer X32 and have been trying to connect Waves Multirack software via USB to the XUF FireWire/USB audio interface card. My hopes are to be able to run all the audio inputs during live performance through the Multirack software and back into the X32. I have had some success but have not yet found a "routing" combination that has completely worked. Has anyone tried and done this successfully??

      I am new the forum and would appreciate any thoughts.

      Best,

      Hoyt




      As long as you want to set up as insert on every channel, it is quite straightforward. If you route Card out to use Local 1-8, 9-16, 17-24 & 25-32 and route Inputs to use Card as source, you have insert on all your channels. You have to do any bypass in Multirack, and all channels have to have a path trough Multirack, but the X32 side is fairly straightforward if you can live with having permanent inserts.



      One question for you, does the Multirack support non-Waves plugins, I have a couple of Waves bundles and would like to use them if that doesn't limit me to Waves-only.
      • January 13, 2013
  • BobHarvey
    Contributor - Level 2
    2012-08-22
    Have any of you early adopters located a case for the X32?

    I corresponded with Gator last month and they seemed oblivious to the wave of X32s that's about to come ashore.

    Our friends across the pond are getting a nice case from Thomann, but shipping from GB would be a bit much!

    http://www.thomann.de/gb/thon_case_behringer_x_32.htm

    Partick Ferdig, VP, CARE - MUSIC Group Services US Inc., is checking with product management to see what he can find out regarding a flite case for the X32.

    Thanks ...
    read more...
    0 9,019
Go to page