Statistics

165,429 members
180 posts
  • 1224
    Contributor - Level 1
    2019-11-23

    How do I hook up a monitor speaker to my Europort 2000bt?

    0 85
    • 1224
      KenMitchell

      Hi Tony ( @1224 ), 


       


      Welcome to the community.  The 2000BT doesn't really have a monitor bus nor an aux output.  The best you could do would be to connect a powered monitor speaker to the "Record Out'. However, this would just be a copy of whatever was coming out the Main speakers. 


       


      Hope this helps, 


      Ken

      • November 24, 2019
  • trapiche
    Contributor - Level 1
    2019-11-20

    Hi all!
    A week ago I bought a B115W, for now I only use it to listen to music in my house. But I have noticed that the rear control panel gets quite hot (near burning the hand) despite being at a soft volume.
    In theory it is a class D amp with SMPS power supply and should run cool ....
    What is the normal operating temperature?
    thanks to everyone

    read more...
    0 52
  • pendragon
    Contributor - Level 2
    2019-11-17

    I have a new gleaming set of Ardens and also a wood burner which does create some fine dust over time. How is it best to keep the drivers free from dust. Some say a vacuum cleaner (!) others a soft brush and yet others a dust blower. Anyone got the answer? Thanks

    read more...
    0 73
  • BobKraus
    Contributor - Level 1
    2019-07-19

    I have been trying to get this to work using the instructions, but they just seem to be missing a step. I would like to use the Turbo Control App to control both of my IP1000s, but I can only seem to get one to be controlled. The Master/Slave feature doesn'r seem to work either... Any help?

    read more...
    0 150
  • AyChords
    Contributor - Level 3
    2019-11-10

    I bought a subwoofer THRUTH B2029A (fairly used) on eBay, and after carefully reading the manual and following the voltage selection procedures, I powered on the subwoofer. After awhile (5min) I discovered the woofer was seriously heating, and shut down after some minutes. I thought it was disconnected from the mains but not. I troubleshoot (checked and replaced the fuse) but it was not coming up.
    Later I discovered the toroidal transformer is faulty.
    Now I want to replace the transformer, what’s the specifications I should be looking for.? And what’s the voltage that enters to the PCB of B2029A?

    read more...
    0 105
  • mrbklowe
    Contributor - Level 1
    2019-10-30

    Any idea on how to safely remove front speaker grill cover on Behringer B215XL to replace driver. No screws are located on the front grill cover. 

    0 123
  • etiuda
    Contributor - Level 1
    2019-10-30

    Does the USB connection work only with Behringer Digital Wireless mics or will it work with other brands? Thanks   

    0 191
  • asui
    Contributor - Level 1
    2019-10-29

    Where can i relocate the Top columns for the turbosound ip 3000 for purchase  thanks

    0 68
  • FrankHarlan
    Contributor - Level 2
    2019-10-02

    I can here a signal from the HF driver, but nothing from the LF driver. I have updated the firmware and it did not fix the problem.  Any suggestions?

    0 148
    • FrankHarlan
      Paul_Vannatto


      @FrankHarlan wrote:


      I can here a signal from the HF driver, but nothing from the LF driver. I have updated the firmware and it did not fix the problem.  Any suggestions?





      Hi Frank,


      Welcome to the forum. Have you had a look at the EQ or crossover settings in the DSP? It may have a very high high-pass setting.


       

      • October 2, 2019
    • FrankHarlan
      MatteoBarbaro

      Hi Frank,



      I think that shoud be the connector between the amplifier and the LF speaker, if you don't solve the problem with the suggestions of Paul of course. Remember that iQ loudspeakers are Two way biamp, so you have two amplifier output, one for each way.


      If it's in warranty i suggest you to contact your reseller.



      Regards,



      Matteo

      • October 28, 2019
  • hapeyo
    Contributor - Level 1
    2019-10-23

    Hello, i bought the europort 2000bt in the united States. Now i am living in Chile and have to change al my stuff to 220 V. Anyone can explain the planet earth switch: ""Planet Earth" switching power supply for maximum flexibility (100- 240 V~), noise-free audio, superior transient response plus low power consumption for energy savings."

    i dont know how to switch. Is it only the changing of the fuse?

    read more...
    0 58
Go to page