Statistics

165,365 members
43 posts
  • texasboy112
    Contributor - Level 2
    2020-04-02

    Hi,  I just ordered a Hall of Fame 2 X 4 Reverb Pedal (TC Electonic).  On their YouTube video they show Colored Buttons that cover the (4) Bottom Push (MASH) Knobs.  Not only do they look great, but I can see that it would make using the pedal easier.  Can some one (Please) tell me where I can piuchase them, I'm not having a lot of luck so far.  THANKS

    read more...
    0 32
  • GregWarren
    Contributor - Level 3
    2020-03-25

    This is my set up and I wanting to record the 32 channels. I can see the sounds off the board going into logic, but when I record them it sounds like a alien trying to communicate with me. 

    0 106
    • GregWarren
      DaveMorrison

      @GregWarren 


      It sounds like you have a sample rate mismatch. Set both Logic and the DN9630 (and the mixer) to 48 kHz.

      • March 25, 2020
    • GregWarren
      GregWarren

      Thanks for replying...It all is...switch on 48K on DN9630...midas is set to 48k and so is logic...I've checked multiple times

      • March 25, 2020
    • GregWarren
      DaveMorrison

      @GregWarren 


      My first thought of alien communication was a samples played at the wrong rate. You are getting some sort of signal from the DN9630 though? Hmm... 

      • March 25, 2020
  • Galiano
    Contributor - Level 1
    2020-03-25

    Hola hoy me llegó el controlador vocal TC Helicón perform-v, al conectar la alimentación todas las teclas de mantienen encendidas en su color de On,  no cambiando de color por mucho que las toque. Es un defecto del producto? O un error de puesta en marcha y tengo que hacer alguna operación? Los efectos funcionan correctamente, pero al no cambiar los colores es complicado saber qué efecto está en funcionamiento. Me podéis ayudar ?

     

    read more...
    0 31
  • DanieleCAS
    Contributor - Level 1
    2020-03-23

    Hello, 

    i need suggestions about delays. I'm searching some tc electronic's delays and I'm so uncertain about the choice to make. 

    I saw the d-two and the g-major2. Are the delays similar in the 2 multifx systems?

    Also the flashback 2 is comparable to the previous effects? I prefer the display and a rack system so the d-two or g-major 2 are perfect for me but I don't know which effects to buy and which is better.

    Help me in my decision, in know that g-major2 has other effects that I honestly don't need.

    Thank you.

    read more...
    0 42
  • SpeedyPeavey
    Contributor - Level 1
    2020-03-17

    Recently bought a second hand g system. Going thru Lairds config and got to relays for amp channel switching. Set patch 001 up to switch to clean and 002 for crunch, but then 003 wouldn't select (or 004, 005).  What am I doing wrong?

    0 41
  • Pavel1
    Contributor - Level 1
    2020-03-14

    Hi, I have a problem stopped working Display on M-ONE XL. Illuminates but does not show anything can it be fixed somehow? Or the only chance is to buy a new one ??? Thank you for info Pavel

    0 42
    • Pavel1
      RexBeckett

      @Pavel1 


      Hellp Pavel, welcome to the community.


       


      I suggest that you raise a Care ticket for Service Repair explaining your problem. This is done by clicking on Support at the top of the page and then clicking the Create a Care Ticket button. This is only possible if you have completed all the required fields in your profile. Make sure that you fill-in every required field on the Care form.

      • March 14, 2020
  • Stephenp
    Contributor - Level 1
    2020-03-11

    Hi,

    Have tested using the CP8000 but as it doesn't use a rotary encoder, it will not work safely for mixing volumes. Due to the volume jumping to the position on the volume know when you change buttons.

    Is there a way to include a rotary encoder in system? or would I have to go to rs232?

    Thanks,

    Stephen

    read more...
    0 65
  • AndersonGuerra
    Contributor - Level 1
    2020-03-10

    Hello fellows...1st post around here...

    I have a TC Finalizer Wizard Series 48k and the display backlight is not working anymore, the display itself is working.

    I had a tech to look around and see if it was something visible like a missing voltage or bad cap.

    he could not find anything. any tips on fixing this or where to buy a new display?

    Cheers, Anderson.

     

     

     

     

     

     

    read more...
    0 63
    • AndersonGuerra
      PedroRodrigues

      Hello Anderson


      In that case please enter the SOFTWARE BOOT menu, by keeping HELP button pressed at power on. Dial option to INFO and press OK to check the application software. If corrupted; load the application software again.


      I hope it helps...


      All the best


      Pedro


       

      • May 13, 2020
  • TonyFry
    Contributor - Level 2
    2020-03-10

    I've posted about this before and never really got a satisfactory answer, so I'm hoping for a better result this time. I want to record loops to a particular preset so I can integrate it into live performance. The problem is that I record a loop, save it to (say) preset 20, which is fine. However, the saved loop is then on every preset, which is completely useless.......
    Then, when the loop is erased, it comes back when the VL3 is switched off and back on again. 
    Someone suggested saving to a different slot within the loop but this doesn't work either. I want to save maybe 50 different loops to 50 different presets and I'm pulling my hair out trying to find a resolution. Can anyone help? Please ......?

    read more...
    0 134
    • TonyFry
      TCH-Rob

      What are your slot settings in the "looper" menu? Loops aren't saved to presets, but to one of the 50 loop slots; each loop slot saves loops A, B, and C. You can change your loop slot using the preset up down switches in the "UTIL" page in the looper. If you save the preset it will store the loop slot you had selected. 


      What likely happened is you had the same loop slot selected on multiple presets. Once you saved a loop to that slot, that loop was also selected on those presets. 


      Hope this helps, let me know if you have any questions!  

      • March 11, 2020
    • TonyFry
      TonyFry

      Hi TCH-Rob,


      Many thanks for this. I’m kind of discovering this for myself. I got hold of the latest User Manual for the VL3 yesterday and it has a much better section on the subject than the older manual I was trying to work from.


      I’ve got the basic gist of it (I think) but I do have a question. If I start to save slots to particular presets, should I leave slot 1 free for looping “on the fly” for other presets that don’t have any saved loops?

      • March 11, 2020
    • TonyFry
      TCH-Rob

      Hi @TonyFry ,


      I think that's a great idea; I'd probably leave slot 1 open because that's the slot that most presets default to.

      • March 12, 2020
    • TonyFry
      TonyFry

      hI @TCH-Rob 


      Hope you're well in these difficult times. I have a further question. I've been trying to use the Onsong midi capability to change the Step (according to the VL3 CC list it's CC No 115 plus a value that equals the required step number) but it doesn't seem to work. All other program changes work well via midi but i cant get this CC to work. Is there a VL3 setting that would enable this feature or does it just not work? The CC controls work well with other equipment such as BeatBuddy, so I'm wondering if I'm doing something wrong?


      Look forward to your reply.


      Best wishes, and stay healthy.

      • March 30, 2020
    • TonyFry
      TCH-Rob

      @TonyFry I've reached out to our testing team about this; that isn't regular behaviour, hopefully it isn't an issue with your indiviual unit!

      • March 31, 2020
  • mochiji
    Contributor - Level 2
    2020-03-08

    It seems that DM KONTROL misidentifies DM8000 as DM8500 and compatible erorr is displayed on Device Connect windows.
    Clicking on the open control surface displays an error message. DM KONTROL seems to recognize DM8000 as DM8500.
    However, the detail display shows DM8000. How can this be solved?DM8000 error.jpg

     

     

    read more...
    0 55
Go to page