Statistics

165,426 members
175 posts
  • KikeVila
    Contributor - Level 2
    2019-06-17

    Mi deepmind 12 era un premio... mi primer sinth de verdad.
    Vino con un fallo en la calibración de la rueda de pitch
    Dos meses en el taller

    Volvió... con un fallo, un ruido raro asociado al ventlador,  lleva mes y medio en taller y aún no sé nada.
     Me supuso un esfuerzo economico grande, era una necesidad. Aposté por marca y modelo emergente, Me ha salido el tiro por la culata. 
    Si, volverá, pero con que fallo ?  
    No les importa nada, soy el número malo de las estadisticas, 
    Korg nunca me falló.
    Si, una maquina maravillosa, yo no me merecía esto.

    Vaya metida de pata tan grande, , podria haber comprado un korg, o roland , o sequential... 
    Vale, se me pasará... pero ahora estoy muy triste, no tengo pasta para un prophet.

    read more...
    0 129
  • jackduk
    Contributor - Level 1
    2019-06-10

    After sitting on my desk for just a few weeks, I've noticed dust building up on my Deepmind 12D which I'm worried about as their are gaps in the sliders where dust is obviously going to gather. 

    Headed over to Decksavers as Facebook must have heard me mention it and then advertised it on my feed and their covers are tip top. Only thing is, they don't do any for Behringer! 

    Anyone know why? Or if any alternatives are out there that look just as good? 

    read more...
    0 658
  • shushstudio
    Contributor - Level 1
    2019-06-05

    Hi there, I have a major problem. The first time I used my Deepmind 12 connected via USB midi (I had previously used it not connected to check out the sounds) there was some kind of malfunction as it played itself, and even when I pulled out the USB midi lead, it continued to play.) I thought it might have been a problem with the synth itself so, I tried it again and eventually decided to update the firmware but to no avail. This was cured by trashing Logic X preferences so bad midi instructions must have been being sent. This fixed the autonomous strange play problem. I then noticed that the patches had changed in there sound and were not correct. So I restored the synth using the PROG WRITE key commands on startup restoring all steps 1 -5. Again it made no difference. I downloaded SysEx librarian and ran and installed the factory combined presets using SysEx librarian. However, the original factory sounds have not been re-instated instead I still have the messed up sounds after the midi problem incident.   

    Can anyone help me get the synth back to the original factory patches, it is working fine now apart from this, but sadly is of little use to me as the sound patches are now unusable. Thanks Dx

    read more...
    0 901
    • shushstudio
      Scatterplot

      Your manual shows you how to reset your DM12 to factory defaults, this will reinstate all patches.

      • June 6, 2019
    • shushstudio
      RonaldFigura

      Make sure when you are restoring that the USB cable is disconnected from your computer.

      • July 5, 2019
  • automaticform
    Contributor - Level 1
    2019-06-05

    I opened up a technical ticket 3 days ago and NO REPLY!!!!

    It's been under 30 days and this machine no longer works!!!!

    Only the 440hz sound plays and I have tried everything. It is DEAD.

    The model D is patched to Behringer's own recommended settings to get sound out of it!!!
    When I increase the volume all the way, I hear a tiny click with each MIDI press but that is it!

    I have already tried running MIDI to it from 3 different sources: Ableton, a Keystep, and a Novation Circuit.

    Double-checked over and over that everything is going to the same channel.

    Tried other channels by flipping the dip switches in the back.

    Tried 3 different MIDI cables and quarter inch cables!!!!!!!!!!

    Tried listening through the headphone jack and through the high and low on the back. No SOUND is produced!

    The only thing I can think is that I upgraded from 1.0 to 1.1.1. But it didn't immediately die. I played at least once after the updated firmware.

    24 hours later DEAD.

    Please a REPLY would be nice after 3 days as I can find no phone number to speak to a human.

    read more...
    0 303
  • ristst
    Contributor - Level 2
    2019-05-28
    0 99
    • ristst
      ristst

      I somehow closed the topic before describing my issue.  I want to enable the pormamento but I can't figure out how.  I also want to adjust the range of the pitch wheel, but I can't find any information on how that's done either.


       


      Can someone point me to documentation or a tutorial that shows how to do these things?

      • May 27, 2019
    • ristst
      ristst

      Sorry...PORTAMENTO.  Please excuse my spelling error.

      • May 27, 2019
  • horder2344
    Contributor - Level 1
    2019-05-20

    Hi. If I connect my new MS 101 to my behringer 6 channel mixer using a mono jack output cable to twin left right stereo input on my mixer I get really bad feedback coming though the speakers. If I switch the cable to mono Jack out to mono Jack in on the mixer its completely fine. I have tried different cables and each time if I use a mono to stereo its gets really loud feedback. Does this sound like a faulty unit? Thanks.

    read more...
    1 151
    • horder2344
      RonaldFigura

      I don't know for sure, but if the MS 101 output is mono, using a mono to stereo adapter cable will not yield desireable results. This is why most mixers and/or amplifiers have a "left/mono input. You cannot get stereo from a mono source. Most older synths (Minimoog, ARP Odyssey, etc) were mono. 

      • July 8, 2019
Go to page