Statistics

165,363 members
41 posts
  • gtcode
    Contributor - Level 2
    2019-09-25

    Hi, I haven't bought a P16-m yet. Will the bracket P16-mb allow the P16-m to be mounted to a high hat stand with the unit facing the drummer at a reasonable angle?

     

    Also I looked online but wasn't able to find any info on the mounting holes. I'd like to devise a custom mounting solution if the bracket won't work, before buying it. Anyone have info on this?

     

    Thanks!

    read more...
    0 168
    • gtcode
      gtcode

      Just answering my own questions. From a photo I found it looks as though the P16-mb will work fine with a High Hat stand.

      • September 25, 2019
  • DavidC3Av
    Contributor - Level 2
    2019-08-24

    Could someone pls advise about whether it is possible to connect Behringer P16 to DL153. We have MIDAS M32R and DL153 stage box. P16 works fine off the mixer desk M32 Ultranet port, but the DL153 manual is silent about whether the DL153 Ethernet Control can send Ultranet. Is this possible or are we going to have to run a separate RJ44/Cat5 cable from the M32 to the stage for Ultranet? If DL153 cannot run Ultranet, what is the cheapest alternative to running an additional Cat5 cable to provide Ultranet connectivity on stage? Thanks in advance, David. 

    read more...
    0 595
    • DavidC3Av
      DaveMorrison

      Hi @DavidC3Av 


      No. Ultranet is neither AES50 or Ethernet. The DL153 doesn't have ultranet capability. The Midas DL 32 & 16 and Behringer S32, S16, SD16, SD8 all can do ultranet because they have the proper chipsets. Channels 33-48 on the AES50 bus are then routed by the stageboxes to the ultranet ports. Theoretically it might be possible to send signal to a SD8 and then daisy-chain to the DL153. Maybe someone on the forum has done it.

      • August 24, 2019
    • DavidC3Av
      DavidC3Av

      Thank you Dave, much appreciated. Looks like an elegant solution, and low enough cost to order and give it a shot next Sunday. Do you think it might be possible to daisy chain the SD8 after the DL153? Ie. even though DL153 doesn’t have Ultranet chipset that it is likely to faithfully pass on whatever protocol is happening on the AES50 for the SD8 to put out the Ultranet? Thanks again.

      • August 24, 2019
    • DavidC3Av
      GaryHiggins

      @DavidC3Av AFAIK you can't daisy chain any of the midas "blue" series stageboxes. The second aes50 port on those is redundant meaning if one fails the other will keep working when connected to a Midas Pro series mixer. It's not an in/thru type line. When using with the X32/M32 series mixers, it can be used on one aes50 port and nothing can be daisy chained beyond it on that line, In that regard they become somewhat limited. However your SD8/16/32's can be used on the other remaining X32 aes50  port and daisy chained normally up to the 48 ch limit.

      • August 24, 2019
    • DavidC3Av
      DavidC3Av @GaryHiggins thank you. Would inserting the SD8 before the DL153 on that AES50 work?
      • August 24, 2019
    • DavidC3Av
      GaryHiggins

      It may, I am not sure, I would wonder how/if the S/SD boxes can pass forward the ch's of the DL153 box properly to the mixer due to the ch shift they normally impose and implement with regard to each other. You might not achieve proper sync. I might guess no but it's just a guess. @ChaseMcKnight would be the guy here who would know for sure.


       


      @RexBeckettsorry did not see your post before writting my response...


       

      • August 24, 2019
  • KingBurton
    Contributor - Level 2
    2019-07-08

    Are thees outputs Hiz only or TRS?

    0 174
  • staceyhainey
    Contributor - Level 3
    2019-06-07

    Just a general question,,,,

    My band just purchased an M32C with the DL32, and PM16’s for monitoring 

    i split the vocal, and instruments into mix busses, and sent the busses to ultra net, but it seems like we aren’t getting the full signal (some busses seem absent on the pm16)   We do have something that kind of works, but there’s gotta be a better way 

    will post a screen shot of the routing pages

    read more...
    0 285
    • staceyhainey
    • staceyhainey
      RexBeckett


      @staceyhainey wrote:


      Just a general question,,,,


      My band just purchased an M32C with the DL32, and PM16’s for monitoring 


      i split the vocal, and instruments into mix busses, and sent the busses to ultra net, but it seems like we aren’t getting the full signal (some busses seem absent on the pm16)   We do have something that kind of works, but there’s gotta be a better way  


      will post a screen shot of the routing pages





      @staceyhainey 


      Where are you connecting the P16Ms - to the M32C or the DL32? If the DL32, you need to open Routing -> AES50 A/B and select AES50-A 33-40 = Ultranet 1-8 and  AES50-A 41-48 = Ultranet 9-16. This will send the 16 Ultranet outputs to the DL32 on AES50-A 33-48 which are routed to the P16 socket.  


       

      • June 7, 2019
  • shiyah
    Contributor - Level 1
    2019-06-04
    0 201
Go to page