Statistics

165,363 members
41 posts
  • RalphHopstaken
    Contributor - Level 3
    2020-03-11

    Hello,

     

    Is it possible to disable the solo function when adjusting the Volume of an individual channel in a group?

    the reason I ask is when I use PD48 when I'm playing and notice that for instance a vocal in a assigned vocal group needs adjustment . When I press the Vocal group button and press Edit to adjust the volume of one vocal it solo's so i can't hear my own (keyboards) playing and the rest of the band any more.

    read more...
    0 68
  • daniciuc
    Contributor - Level 1
    2020-03-04

    Hi everyone,

    So I'm using two M32 consoles, one for FOH and one set up as monitor console.

    I'm at the limit with channel inputs and I would like to go furter and buy a Wing, but I don't know how to mix the extra channels from the Monitor console ... Do you guys have any ideas? or suggestions? Or should I just buy 2 WINGs ...

    Hope I was clear enough

     

    read more...
    0 89
    • daniciuc
      GaryHiggins

      Hi @daniciuc 


      I think you will need two Wings to mix a full 48/96 ch's at both places at once. Except maybe FOH doesn't need to mix all sources for the show, in which case maybe the Wing in monitor world M32 FOH might do it....but what the hell, buy 2!!

      • March 3, 2020
    • daniciuc
      Paul_Vannatto

      Hi Emanuel @daniciuc 


      Welcome to the forum. As Gary @GaryHiggins mentioned, if the budget allows getting 2 Wings would definitely be the best solution. But if the budget is tight and since you already have an M32, the Wing and M32 can function together. If all of your inputs are mono in nature, all you are gaining (input-wise) are 10 additional channel strips (48 instead of 38). But if some of the inputs are stereo, the difference in inputs increase significantly. 


       


      Gary did bring up an important point with regards to input requirements that differ between FOH and monitor worlds. I find that FOH tend to require more inputs than monitors. Most musicians want specific channels, not the "whole enchiladas". But that may generate complex (creative) routing in order to accomplish this, particularly with the bank of 8 limitations. With the 2 Wing system, that routing complexity disappears (since the bank of 8 limitation is non-existent). 


       

      • March 3, 2020
  • colino_ltapl
    Contributor - Level 2
    2020-02-19

    Hi guys, 

    I have a question and i hope we all can learn from each another. 

    Recently i have updated the firmware of the DP48 to 1.2, after which i am not able to remote control the other units via the 1st unit. 

    Is there a minimum unit to setup in order to do remote control of the other unit? Or is there a special CAT5 Cables we should be using in order for the connectivitiy to get thru. 
    Please take note that all my 5 units has signals passing thru from the M32 Console. 

    Hope to hear from you guys.

    Cheers!

    read more...
    0 169
    • colino_ltapl
      Paul_Vannatto


      @colino_ltapl wrote:


      Recently i have updated the firmware of the DP48 to 1.2, after which i am not able to remote control the other units via the 1st unit. 





      Are you trying to change the group names and assignments from the first DP48 or from the M32? If it is from the first DP48 (in the chain), do you have it set  with the remote on (its device ID should say MSTR) and the rest should have remote on and should have unique device ID. Once that is setup, on the master (first) DP48, goto the Broadcast line and press the encoder. 


       


      If you are trying to send from the M32 Library, AES50 screen, we found a bug which the fix will be part of the next release.


       

      • February 19, 2020
    • colino_ltapl
      colino_ltapl

      Hi Paul,


      Appreciate your replies. 


      just to recap, the first DP48 on master and the rest are on their on IDs, after which punch in the broadcast on the first unit and select the other unit ID to control them correct? 


      Unfortunately it doesn't seems to be working. Did i miss out any step?

      • February 19, 2020
    • colino_ltapl
      Paul_Vannatto


      @colino_ltapl wrote:


      Unfortunately it doesn't seems to be working. Did i miss out any step?





      Did you turn on Remote on all the DP48's before pushing the Broadcast?

      • February 19, 2020
  • TONKLA
    Contributor - Level 1
    2020-02-19

    I bought a pair of Nekkst K6 (Brand new) and found that 1 piece has two defection spot on a subwoofer.

    Could I claim this piece of speaker with a Distributor in my country ?

    41238.jpg
    read more...
    0 31
  • ssamedia
    Contributor - Level 1
    2020-02-05

    I have an AMP800 headphone amp trying to order original power supply can't find anyone ever have to replace before? If so was it a generic vs original?

    0 61
  • stevejacobsen1
    Contributor - Level 1
    2019-12-14

    What's the difference between the level contols for main and the output level control?

    0 278
    • stevejacobsen1
      MusicallySavage

      Hi Steve,


       


      What do you mean? What sort of product are you talking about?


      The term MAIN is generally reserved for an overall Master volume control, and Output level control might be for several individual signals that a device is able to control. That might be for a mixer, or, I'm guessing on this particular forum, 2x Aux Sends from a mixer into your In-Ear-Monitors. The Output level controls how much of each signal you receive, and the Main controls the overall volume.


       


      Cheers, Luke

      • December 24, 2019
  • marianorusso
    Contributor - Level 1
    2019-11-22

    I need to activate warranty support (as required by your Support Request Response (Case: 01.032.712)
       communicating: • current postal address (including City / Postcode / Country) via gabriele jannelli 23 80129 napoli italy
    • Serial number of your item (foto)
    • Proof of purchase * enquire  pdf
    to obtain RMA number and service center.
      do you give me instructions?

    [email protected]
    serial mixer beringer.jfif

    fattura beringher mixer.pdf
    read more...
    0 110
    • marianorusso
      GaryHiggins

      @marianorusso They have stopped putting date code stickers on a lot (if not all) of their products. Your date code would by March 2018 which is the first 4 digits after the S in the serial number.

      • November 21, 2019
  • AyChords
    Contributor - Level 3
    2019-11-10

    I bought a subwoofer THRUTH B2029A (fairly used) on eBay, and after carefully reading the manual and following the voltage selection procedures, I powered on the subwoofer. After awhile (5min) I discovered the woofer was seriously heating, and shut down after some minutes. I thought it was disconnected from the mains but not. I troubleshoot (checked and replaced the fuse) but it was not coming up.
    Later I discovered the toroidal transformer is faulty.
    Now I want to replace the transformer, what’s the specifications I should be looking for.? And what’s the voltage that enters to the PCB of B2029A?

    read more...
    0 199
  • Krabbe
    Contributor - Level 1
    2019-11-05

    Hi 

    I've got a band with 7 member, who's considering buying a P16-system. Recently I stumbled upon the DP48-system, which, to me, seems more attractive than the P16-system.

    However, I'm interested in knowing if it is possible to daisy chain multiple DP48s and if so, how many units can be daisy chained?

    Fingers crossed that someone can help me out

    /Krabbe

     

    read more...
    0 710
    • Krabbe
      GaryHiggins

      @Krabbe Paul or Robert will know for sure but the units use aes50 and not an ultranet port, they have an in and a thru aes50 port and power is supplied using POE so I'm sure you can link "many". The ultranet port of the p16 with p16D's added could support I believe up to 64 p16M's? Anyway I'm sure at LEAST 4 could be linked, with each supporting 2 mixes-that would give 8 people mixes of their own. My guess is it would support many more, but I'm a guesser!


      https://www.midasconsoles.com/Categories/Midas/Signal-Processors/In-Ear-Monitoring/DP48/p/P0BMX#googtrans(en|en)


       

      • November 5, 2019
    • Krabbe
      KenMitchell

      I think it might also depend on what the functionality of the "yet-to-be-released" HUB4 is when it comes to the remote configuration and also the back-channeling of the mixes.  That could limit the number of DP48s in a chain. 

      • November 5, 2019
    • Krabbe
      GaryHiggins

      @KenMitchell The Hub4 kind of sounds like the dp48 equivalent of the P16D, I'm guessing (I do a lot of that) it takes an aes50 line, adds the POE component and supplies 4 dp48's which can each then pass on 1 via aes50 thru (they each have a thru)? As you said that bidirectional aes50 48 ch count makes things a bit sticky. Can't wait to find out! I'll get 10 or so to go with my new WING

      • November 5, 2019
    • Krabbe
      Paul_Vannatto

      Hi @Krabbe,


      I can provide some insight regarding this new personal mixer. Daisy chaining of the DP48 is done in a similar manner to the P16's in that each DP48 has input and thru AES50 ports and would require the included power adapter. The Hub4 provides POE on the AES50 to eliminate the need for the power adapter if the DP48 is connected directly to it (similar to the P16-D). 


       


      The Hub4 is a 1U form factor that provides for up to 4 DP48 as well as input and thru AES50 ports. But it also has a lot of routing flexibility in it. One of the features is that you can connect up to 8 stereo IEMs to the back of it, that are mixed from the connected DP48. Each DP48 can accommodate 1 or 2 musicians. 


       


      I've been beta testing these since the beginning of July with 9 tribute bands (from all over Ontario, Canada) and 9 local bands - and everyone loved them. One of the events was a Woodstock 50th Anniversary (Aug 16) that had 1 local band and 5 tribute bands in 9 hours. That allowed approximately 30 minutes between bands. As part of the transition, I had to set gains (only one band showed up for soundcheck), show everyone how to use their DP48's, change mic placement, etc. At the end of each set, I got rave reviews from each of the bands. That shows how user-friendly the DP48 can be - if the sound engineer is prepared to spend some time ahead of the event setting it all up (and the riders from the bands are up to date and accurate).


       


       

      • November 5, 2019
    • Krabbe
      GaryHiggins

      Hey Paul @Paul_Vannatto , so what is the real world limit to the number of DP48 units on a single mixer? Have they said? Can a stagebox be cascaded off (and back thru) a DP48 or Hub4? In other words if you use the DP48 on a port A or B of a mixer, is that port more or less used up or can other things still be connected? Also the aes50 assignments, are you "stuck" with the ch assignments used on a port (A or B) elsewhere for the available DP48 ch's? For instance say I use out 1-8, out 9-16 for mixbuses and foh and have 17-24 set for say aux1-6/M and then say card 1-8 for 25-32 and p16 for the rest. Are these then then also aes50 ch choices for the DP48? If so it would seem then that one might be better off keeping one port exclusively for the DP48's and use the other port for other mixers and stageboxes?

      • November 5, 2019
  • SinisterDamned
    Contributor - Level 1
    2019-10-23

    I have a pair of studio 50 usb monitors. They are out of warranty the shop said. I want to know where I can buy the circuit board for it so to replace on my own to save a few $$$. Yes, I'm cheap. Photo attached from the repair shop.

    74574258_10158984705979745_7607716730076397568_n.jpg
    read more...
    0 124
Go to page