165,420 members
156 posts
  • 1224
    Contributor - Level 1

    How do I hook up a monitor speaker to my Europort 2000bt?

    0 85
    • 1224

      Hi Tony ( @1224 ), 


      Welcome to the community.  The 2000BT doesn't really have a monitor bus nor an aux output.  The best you could do would be to connect a powered monitor speaker to the "Record Out'. However, this would just be a copy of whatever was coming out the Main speakers. 


      Hope this helps, 


      • November 24, 2019
  • trapiche
    Contributor - Level 1

    Hi all!
    A week ago I bought a B115W, for now I only use it to listen to music in my house. But I have noticed that the rear control panel gets quite hot (near burning the hand) despite being at a soft volume.
    In theory it is a class D amp with SMPS power supply and should run cool ....
    What is the normal operating temperature?
    thanks to everyone

    0 52
  • AyChords
    Contributor - Level 3

    I bought a subwoofer THRUTH B2029A (fairly used) on eBay, and after carefully reading the manual and following the voltage selection procedures, I powered on the subwoofer. After awhile (5min) I discovered the woofer was seriously heating, and shut down after some minutes. I thought it was disconnected from the mains but not. I troubleshoot (checked and replaced the fuse) but it was not coming up.
    Later I discovered the toroidal transformer is faulty.
    Now I want to replace the transformer, what’s the specifications I should be looking for.? And what’s the voltage that enters to the PCB of B2029A?

    0 105
  • yaboymichaeld
    Contributor - Level 1

    Hi all,

    I just purchased a pair of Behringer DR - 115 DSP'S and got to try them out today.

    Very nice sounding speakers and a lot of control with the DSP in terms to EQ's and crossovers etc.

    I'm a bit confused though in regards the limiting applied to this speaker it seems to display LIMIT on the LCD randomly. It's doesn't matter what level the input is at it will say LIMIT at low volumes and at high.
    This is annoying as honestly I don't know where the true limit is of the speaker.

    I'm running from Pioneer decks via XLR to the Behringer. volume on the Pioneer is at 12 OClock and the output meter reads -16db or so . Input gain is at 12 oclock and the volume on the LCD is at 0DB on the Behringer.

    There is an input meter which monitors input on the LCD of the Behringer and this is 1/4 of the way full when playing something through the speaker, I feel I'm nowhere near clipping either.

    I'm wondering if anyone could either shed light on any similar situations like this they had or if (God forbid) I should send the speakers back.

    1 122
    • yaboymichaeld

      Are you hearding noticeable level differences when the limit is displayed?  Maybe it is a soft limit to protect from peaks.  What listening mode are you in (DJ, Live, etc.)?  What is the source of the music?  (many downloaded mp3's have unwanted artifacts that may be triggering this).

      Will the speakers still get loud or is the limiter choking the level?

      I wouldn't be bothered by a limiter coming on.  That is different than a peak or clipping display.  I wonder if certain listening modes have a lower threshold on the limiter?

      • January 13, 2020
  • mrbklowe
    Contributor - Level 1

    Any idea on how to safely remove front speaker grill cover on Behringer B215XL to replace driver. No screws are located on the front grill cover. 

    0 123
  • etiuda
    Contributor - Level 1

    Does the USB connection work only with Behringer Digital Wireless mics or will it work with other brands? Thanks   

    0 191
  • hapeyo
    Contributor - Level 1

    Hello, i bought the europort 2000bt in the united States. Now i am living in Chile and have to change al my stuff to 220 V. Anyone can explain the planet earth switch: ""Planet Earth" switching power supply for maximum flexibility (100- 240 V~), noise-free audio, superior transient response plus low power consumption for energy savings."

    i dont know how to switch. Is it only the changing of the fuse?

    0 58
  • DruMcCoy
    Contributor - Level 1


    These two lights now only come on, when I turn on the power for my speaker. Why? Thanks for an assistance in advance.

    0 118
    • DruMcCoy

      @DruMcCoy wrote:

      These two lights now only come on, when I turn on the power for my speaker. Why? 

      Do the come on briefly then turn off, or do they stay on. If it is the latter, you have a hardware problem.


      • October 19, 2019
  • Poysippi
    Contributor - Level 3
    I am looking for a replacement speaker for my Behringer EUROLIVE B15500XP. I purchased this unit used and have no warranty (bad choice in hindsight) I would love to get this back up in running Kip-
    0 65
  • JuliaSP
    Contributor - Level 1

    Hi,  I got an email about your new product C210 column speaker.  I was literally about to listen to/possibly buy some other brands but thought I'd hold off as I ahve a Behringer mixing desk, and thought I'd check it out.  Looked up ALL the websites for the suppliers one has details on the weight of the unit, spec, costs, when it's all going to be availalble? Anyone know?  

    Thanks in advance.  


    0 408
Go to page